Enable on board video card (9930 Views)
Reply
Honor Student
mpl8570
Posts: 2
Member Since: ‎10-05-2011
Message 1 of 5 (9,930 Views)

Enable on board video card

HP 6000 Pro MT WIndows 7

 

I need to enable onboard video card after install a dual video card.  It is an NVIDIA card from HP with Dual DVI for the PCIe slot.  I am trying to run 3 monitors and onboard card will not enable.  There is no place in the bios to enable the onboard card.

Provost
banhien
Posts: 31,283
Member Since: ‎01-29-2009
Message 2 of 5 (9,927 Views)

Re: Enable on board video card

Hi,

 

I believe when installing a dedicated video card, system will disable on board card immediately (it disables IGP, no way we can find in BIOS). Some forums say with new H67 and Z68 boards we can do this. In short, we can not do this on the HP 6000 Pro MT.

 

Regards,

BH
***
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Honor Student
mpl8570
Posts: 2
Member Since: ‎10-05-2011
Message 3 of 5 (9,926 Views)

Re: Enable on board video card

I have done it with a PCI card but it is older and does not have windows 7 drivers.  It would blue screen about once a week.  I thought if I got a new HP card I would eliminate that problem. 

Provost
old_geekster
Posts: 9,384
Member Since: ‎11-21-2008
Message 4 of 5 (9,924 Views)

Re: Enable on board video card

Mpl, welcome to the forum.

 

Normally, the integrated video is disabled when you install a discrete video card.  Here is what it says in the Hardware Reference Guide in Table 1-3 Rear Panel Connectors:

 

"The monitor connectors on the system board are inactive when a graphics card is installed in the computer".


If a graphics card is installed into the PCI or PCI Express x1 slot, the connectors on the graphics card and the system
board may be used at the same time. Some settings may need to be changed in Computer Setup to use both
connectors. For information about setting the boot VGA controller, refer to the Computer Setup (F10) Utility Guide.

 

Please click "Accept as Solution" if your problem is solved.

___________________________
-----------------------------------
HP TouchPad
- 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 9

HP Split 13 x2
- 1.6 Ghz; 4 GB memory; SSD 128 GB; Win 8.0

HP Phoenix ENVY 810-135qe
- i7-4770K (liquid cooled); 8 GB memory; GT 640 (4 GB), SSD (Samsung EVO 840-500 GB); 600W PSU; Win 7 Ultimate

HP Photosmart 7520 AIO


++++++++++++++++++
**Click the Thumbs Up on the left to say 'Thanks'**

Intelligence is God given; Wisdom is the sum of our mistakes!

___________________________
I am not an HP employee.
Teacher
Andrew_P
Posts: 137
Member Since: ‎12-05-2010
Message 5 of 5 (9,919 Views)

Re: Enable on board video card

1. Turn off the computer and wait five seconds.
2. Turn on the computer.
3. When the first screen displays, do one of the following:
4. Immediately press the F10 key. Press the key once every second until a BIOS Setup utility screen opens.
5. Select Advances tab using left and right arrow key on the keyboard.
6. Then Select “ Primary Video Adapter ”  using up and down arrow key , and hit Enter.
7. It will open a small new window,   ON the new small window select Integrated  and hit enter.
8. After it shows Integrated beside Primary Video Adapter in the list on Advances tab, PRESS F10 key to Save the settings and Exit BIOS.
9. Restart the computer and use the Integrated card to connect the monitor.

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation