12-26-2009 08:42 AM - edited 12-26-2009 08:43 AM
Over the past couple of weeks I have been having problems with USB devices on my e9140f. These problems all started when the IR blaster for my Hauppage 1290 TV tuner stopped functioning. I have been troubleshooting since then and the problem still persists.
Symptoms (all are intermittent but more failures than successes)
- connectivity / detection of my 500GB Personal Media drive
- unable to read media cards (SD and Sony) inserted in the card reader
- unable to successfully sync iPods (touch and 3rd gen Nano (media stored on the media drive)
- unable to do backups (again, backing up to media drive)
- Windows 7 64 bit home version
- There are no errors showing in Device Manager
- I have tried the recommended Microsoft Hotfix
but get an error message that it is "not appropriate for my computer"
- I have invoked a previous restore point that I believe was taken before the problems started (not 100% certain.
- I have disconnected all USB devices (printer, webcam) except for the mouse and keyboard.
- I have uninstalled devices in device manager, disconnected the USB headers on the Hauppuage to IR extension board, rebooted, powered down then reconnected and rebooted in an attempt to get the IR blaster working.
As above, however, the problem now seems to be a generalized USB issue, so this partial fix didn't help. I'm at my wits end as not only does my computer not work properly, I have now messed up my wife's iPod touch through a failed Sync. Yikes!
Any help to get things back on track greatly appreciated.
12-26-2009 03:53 PM - last edited on 02-20-2017 02:26 PM by OscarFuentes
When you disconnected all USB devices except the mouse and keyboard, if you didn't power down, press and hold the power button for 5 seconds and them reboot - give it a try.
Here's a trouble shooting USB connections document, it's for Vista but should be the same for Windows 7.
Here's a USB update for your computer.
If you're not sure about the restore point you could go back even further.
You might try to do a repair in System Recovery or a complete System Recovery.
If the problem still persist I would start suspecting either a faulty power supply or a motherboard issue as possibilities.
12-29-2009 10:31 PM
The patch does apply to your system. You probably downloaded the 32-bit patch (default) rather than the 64-bit version.
You can get the patch here (this version will figure out which version to install and install the appropriate one).
01-27-2010 01:36 AM
I have the similar problem with HP Pavillion Elite m9567it.
Originally my computer shipped with Windows Vista 64 bit edition.
I have made a clean install of Windows 7 Ultimate (64 bit) from Technet as I have an active Technet subscription and installed. After installation I've connected my external USB hard drives and there was no problem. Some days later Windows 7 downloaded and installed updates (maybe this is a reason, I don't know) and then I couldn't any more connect USB hard drives. All other USB devices (except my Canon MP450 Series Printer) didn't work. I have no more access to all-in-one card reader, I can't use USB harddrives, I can't connect my cell phone, etc. Everytime it says that Windows is installing a required software and eventually fails to install it. Is there any USB patch for my model?
I have the following in the system information:
Bulk-In, Bulk-Out, Interface USB\VID_0BDA&PID_0152&MI_00\6&2182AFBE&4&0000 The drivers for this device are not installed.
Device PNP Device ID
Intel(R) ICH9 Family USB Universal Host Controller - 2939 PCI\VEN_8086&DEV_2939&SUBSYS_2A6F103C&REV_02\3&11
Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293A PCI\VEN_8086&DEV_293A&SUBSYS_2A6F103C&REV_02\3&11
Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293C PCI\VEN_8086&DEV_293C&SUBSYS_2A6F103C&REV_02\3&11
Intel(R) ICH9 Family USB Universal Host Controller - 2934 PCI\VEN_8086&DEV_2934&SUBSYS_2A6F103C&REV_02\3&11
Intel(R) ICH9 Family USB Universal Host Controller - 2935 PCI\VEN_8086&DEV_2935&SUBSYS_2A6F103C&REV_02\3&11
Intel(R) ICH9 Family USB Universal Host Controller - 2936 PCI\VEN_8086&DEV_2936&SUBSYS_2A6F103C&REV_02\3&11
Intel(R) ICH9 Family USB Universal Host Controller - 2937 PCI\VEN_8086&DEV_2937&SUBSYS_2A6F103C&REV_02\3&11
Intel(R) ICH9 Family USB Universal Host Controller - 2938 PCI\VEN_8086&DEV_2938&SUBSYS_2A6F103C&REV_02\3&11
01-27-2010 06:29 AM - edited 01-27-2010 06:31 AM
Try running the Intel Chip Set update. W7 should have taken care of that issue. Unplug your USB devices when running the update.
HP ENVY 17T-u100, i7-7500U, NVIDIA 940MX, 16GB, 512GB m.2 SSD
HP Photosmart 6520, HP Deskjet 1112
HP Touchpad, HP Chromebook 11
Custom i7-4790k, Z97, 16GB 2400 MHz DDR3, Intel 750 PCI-E SSD, (2)Samsung EVO 840 SSD, Corsair HX650, GTX 980TI, Corsair H75 water cooler
Windows 10 Pro in UEFI mode - production system
Windows 7 and 8 in UEFI mode - test systems
06-11-2012 09:37 AM
Try updating your windows update. Windows Update allows you to download and install these fixes, either manually or automatically, so that your computer is always kept up to date. These updates can include important problem fixes and updates to fix security vulnerabilities, so it's beneficial for you to have these updates installed.
To read more about this try looking here : http://www.techyv.com/article/installation-windows
02-27-2014 10:44 AM
What do you do when none of the USB ports will recognize a mouse or keyboard? There is no other option to connect them, and I have tried every one (including the MB). They are powered up by the USB, but no recognition.
I have had trouble where the ports got flaky on some, but worked on others... then, they all stopped working.