Re: Formosa Motherboard Memory Configuration (149 Views)
Reply
Student
ssteven1
Posts: 1
Registered: ‎12-23-2013
Message 1 of 3 (153 Views)
Accepted Solution

Formosa Motherboard Memory Configuration

I have a Formosa Motherboard in an hpe h8 1220t.  The motherboard specifys it supports   pc3 12800 1600mhz RAM however, I have installed Gskill RAM with the above mentioned specs and it is showing up at a speed of 1333mhz.

 

is there anywhere in the BIOS I can configure this that I am not noticing?

Provost
lasvegaswireman
Posts: 7,541
Registered: ‎07-16-2011
Message 2 of 3 (149 Views)

Re: Formosa Motherboard Memory Configuration

NO, you didn't miss any BIOS setings. Please indicate the amount and full configuration of RAM on your computer.

 

The RAM speed automatically is configured based on the RAM SPD and RAM population. You may try using one stick of GSkill 1600MHz only and see what speed the BIOS reports. If this reports 1600... add another stick and repeat. If using mixed memory modules, the computer usually select the the slower common speed.

 

If you have any further questions, please don't hesitate to ask.

 

Please click the white KUDOS star to show your appreciation


Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V

This is a user supported forum. I am a volunteer and I don't work for HP.

HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240
Provost
Big_Dave
Posts: 18,848
Registered: ‎07-17-2009
Message 3 of 3 (143 Views)

Re: Formosa Motherboard Memory Configuration

Hi,

 

The Formosa motherboard can run either the Intel Sandy Bridge or Ivy Bridge processors.  If your PC has the Intel Sandy Bridge processor then 1333 is all that you will see. If you are running the Intel Ivy Bridge processor then all of the dimms need to be 1600 mhz dimms (same CAS required) to ensure that the dimms will bind up at the maximum speed rating.

 

Custom motherboards will allow faster speeds with dimms using XMP but typically the faster speeds are over clocking the dimms.  Even without using XMP faster speeds can be obtained using manual timing and voltage adjustments. HP doesn't give consumer motherboards over clocking choices except in rare occasions.

---------------------------------------------------------------------------------------
HP e9280t, i7-960, 12GB, Vertex 3 120, ATI 4850
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad
Custom i7-4770k, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-3770k, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation