02-24-2010 04:53 PM
I have a Pavilion m9058n with Vista preloaded. Earlier this week I started to load XP as a dual-boot OS. Things were not as smooth as I had hoped, however I was able to get everything to load. And, with one exception, the system appears to be running good. Drivers are ok. The exception is that there is some kind of error when I put the computer into stand-by and then wake it up. This causes a reboot every time. I read somewhere that this might be caused by incorrect drivers for the hard disk. When I installed the Nvidia mobo chipset drivers I got the following message after it was all done. RAID is enabled in the BIOS and I installed the chpset drivers after most of the other drivers were installed.
1) NVIDIA storage driver optimized for nForce SATA controller that will replace the driver that came with Windows.
2) A RAID controller driver which is required if SATA RAID is ENABLED in BIOS
3) RAID Manager application software
Note for Windows XP:
To install OS onto SATA disks when RAID is enabled in the BIOS, you MUST do the following:
- use the "-x" option with the package .exe to extract storage driver files
- follow instructions for Windows F6 install in "IDE\<os version>\driver\READMEF6.txt"
I installed from bootup. I have no idea where that READMEF6.txt is. Do I need to re-install XP using the "-x" option? If so, I'm not sure how to go about that. Or, should I just use the RUN method on the chipset driver with the "-x" option.
Any help or advice would be greatly appreciated.
02-24-2010 06:05 PM - edited 02-24-2010 06:24 PM
Your XP system is missing a driver which might be causing the problem. Did you look at all the VISTA drivers and look for same XP drivers at this link:http://h10025.www1.hp.com/ewfrf/wc/softwareCategor
I know there are not XP drivers at the above link.
XP lacks sata drivers so before you install XP you need to merge in the drivers with the XP installation disk. Or if you have a floppy drive, have them on a disk (the F6 option).
You can use NLite NLite Guide (it's free) to build a new installation disk and merge in the sata drivers. The drivers need to be a folder and not in installer format. 7-ZIP or Universal Extractor are good at unpacking the installers.
If you started with VISTA on the same HD then you know about the boot record issue.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP ENVY 17t Touch,i7-6500u,6GB, 256 GB SSD (on loan)
HP Photosmart 6520, HP Deskjet 1112
HP Touchpad, HP Chromebook 11
Custom i7-4790k, Z97, 16GB 2400 MHz DDR3, Intel 750 PCI-E SSD, (2)Samsung EVO 840 SSD, Corsair HX650, GTX 980TI, Corsair H75 water cooler
Windows 10 Pro in UEFI mode - production system
Windows 7 and 8 in UEFI mode - test systems
02-24-2010 11:58 PM - edited 02-25-2010 12:43 AM
With the Nvidia 6150SE Chipset, XP will usually install without extra drivers for SATA.I am a bit surprised that XP installed with RAID enabled.
As Big_Dave mentions you do usually need the driver when RAID is enabled so that may be the root of reboot issue. Use one of his suggestions for an extraction tool and extract the Nvidia Chipset to a folder on your hdd. In there you should see one titled ..IDE\WinXP\sataraid with the required drivers.The floppy and F6 can be used ,but slipstreamimg the drivers with nLite and burning a new XP cd works better,imo. Dave has also provided you with the nLite Guide needed. Nlite download: HERE
Your Device Manager actually looks pretty good (to me) , other than Wireless driver missing and the 'Unknown' which I suspect is the ViXS PureTV-U TV Tuner. It is a very elusive one for XP_did you try the one I posted on your other thread without success? Or is the 'Unknown' something else?
The wireless is a bit tricky,since HP gives names to some driver downloads that don't match what you have.Below is a driver which some have reported to work on the M9000 series. If it doesn't work, it will be back to deciphering HP's naming code.
Lite-On Wireless HERE
Which graphics driver do you have installed? Many reboot issues can be traced to them.Go to Nvidia site and choose Option 2 to have it scan for best graphics driver HERE
I have attached the Read Me file from Nvidia Chipset in case you need it.
|**Click Accept as Solution on a Reply that solves your issue to help others**|
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
02-28-2010 11:09 AM
Thank you Big_Dave and CherylG,
After following your suggestions and re-installing XP on a different HD, I was able to get everything working properly. When I installed it before, I had put it on an oooold HD and I think that was what was causing the standby issues. Plus, I hadn't slip streamed the disk drivers onto the installation disk. Plus, I didn't install the mobo driver first off. These were all causing issues, so when I did the install properly, as outlined by your advice, the install went smoothly.
The missing driver is for a TV remote that I don't (and won't) use anyway.
The wireless driver is, and was, functioning correctly. I just have it disabled because I connect to DSL through ethernet. This seems to be a more reliable connection in my case.
Thanks again for all your help,