- HP Support Forum Home
- >
- Laptop & Notebook
- >
- Upgrades
- >
- Re: Replacing LCD/Touchscreen on a DV6T-3000
HP Support Forums
Join in the conversation.
- Subscribe
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
Replacing LCD/Touchs creen on a DV6T-3000
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report Inappropriate Content
04-18-2012 08:19 PM
how do you separate the display bezel from the lcd screen on a dv6t-3000? is it glued or something?
Re: Replacing LCD/Touchs creen on a DV6T-3000
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report Inappropriate Content
04-18-2012 08:24 PM
The following weblink has the steps by steps details:
http://h10032.www1.hp.com/ctg/Manual/c02657339.pdf
Regards,
Vidya
Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
***Click on “Kudos” STAR to say thanks!***
Re: Replacing LCD/Touchs creen on a DV6T-3000
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report Inappropriate Content
04-22-2012 09:56 PM
I guess I needed to elaborate, So I know about the manual and I have used it to rip apart this laptop. There is one step that is confusing, it says to roll the edges when separating the display bezel from the LCD itself. However I am not sure how this is done right without damaging the bezel, it appears to be glued together of some sort. Is this true and how come the manual doesnt explain that it is glued? Thank you for a reply...
Re: Replacing LCD/Touchs creen on a DV6T-3000
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report Inappropriate Content
04-22-2012 10:12 PM
Caution! Observe all precautions when removing and replacing components.
Before you begin: Remove the battery, wireless LAN minicard, hard disk drive, optical disk drive, keyboard, top cover, display panel, display bezel, and webcam/microphone module.
Release the adhesive foil tab covering the logo LED connector.
Disconnect the logo led cable from the display panel cable.
Remove the six 4 mm P1 Phillips-head screws that secure the LCD panel to the display enclosure.
Lift the LCD panel out of the display enclosure.
Please let me know if this helps...
Regards,
Vidya
Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
***Click on “Kudos” STAR to say thanks!***
Re: Replacing LCD/Touchs creen on a DV6T-3000
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report Inappropriate Content
04-23-2012 10:59 PM
I seem to be lost at line 4 and 5 of your explanation. Not sure what your definition of foil tab may be but im not quite seeing one. Nor do I know what the logo LED connector is, dont see anything that says that. I have removed 4 tiny silver philips screws from the two LCD frame rails & 1 from the webcam board. hmmm... I see I might be able to take and upload a pic. this display bezel needs to come off somehow and im just not sure how to do it without ruining something I need to keep. Both the display bezel and LCD screen have to be replaced however, both are cracked on front side. If this helps for a better explanation, please inform me. thank you for all your help so far.
Re: Replacing LCD/Touchs creen on a DV6T-3000
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report Inappropriate Content
04-28-2012 06:48 AM
Hoping for further answer still... YOu sort of disappeared on me. Hope to hear back again. thanks.
