09-21-2012 06:01 AM
- Press the Power ( ) button to turn off the product.
- Verify the input tray is empty, and then check for paper jams, bits of paper, and other obstructions, gently removing any obstructions.
- Lift the top door or the front cover, depending on the product, to access the print carriage, and then check for any obstructions in the paper path.
- Gently remove any paper or other obstructions from the paper path you might find, and then close the print carriage access door.
- Open the rear access door.
- Gently remove any paper or other obstructions from the paper path.
- Check the spring-loaded rear access door rollers to verify that they are clean and can be rolled.
- Check the paper rollers inside the rear access and verify that the rollers are clean and roll upwards.
- Check the star wheel assembly inside the printer on the output side of the carriage. Verify that it is in good condition and clear of paper bits or other obstructions.NOTE:The star wheel assembly is located inside the printer on the output side of the carriage. The star wheel assembly is a set of small, star-shaped wheels on top and rubber rollers on the bottom. The assembly grips the printed side of the paper, and moves the paper to the output tray after printing.
- Replace the rear access door and verify that the rollers on the door and the rollers inside the rear access of the product are "matched up" with each other.
- Press the power ( ) button to turn on the product.
- Plain paper, 20 to 24 lb (75 to 90 gsm)
- Legal size paper, 20 to 24 lb (75 to 90 gsm)
- Card stock, up to a maximum of 110 lb (200 gsm)
- Envelopes, 20 to 24 lb (75 to 90 gsm)
- Photo paper, 145 lb (236 gsm)
- Use only one type of paper in the stack.
- Use 10 to 25 sheets of paper in the stack.
- Fan the stack of paper to make sure that the sheets do not stick together.
- Tap the stack of paper against a hard, flat surface, such as a table top, to make the edges even.
- Insert the stack of paper into the input tray.
- Make sure that the stack of paper is flat in the input tray. Verify the right side of the stack of paper touches the right side of the input tray and that the stack is pushed completely into the tray.
- Position the paper guides firmly against the sides of the paper stack without bending the paper.
- Press the Setup button on the printer.
- Depending on what product you have, perform one of the following:
- Press the arrow key to select Print Report and then press OK.
- Press the arrow key to select Self Test Report and press OK.
- If the test page prints without damaging the paper, you do not need to take any other action.
- If the test page is damaged during printing, proceed to the next step.
- Bits of paper might be obstructing the paper path and need to be cleared.
- Unsupported paper types and sizes might catch and tear in the printer mechanism while printing.
- Paper pushed too far into the input tray when it is loaded, might feed into the printer incorrectly, causing the paper to tear.
- Paper stacks loaded into the input tray with too many or too few sheets of paper, might feed into the printer incorrectly, causing the paper to tear.
- Paper stacks that are not properly stacked when loaded into the input tray, might feed into the printer incorrectly, causing the paper to tear.
- The rollers on the rear access door and inside the product's rear access might not be clean, in good condition or freely rolling.
- The star wheel assembly might be obstructed or have damaged or missing parts, causing the paper to tear.
- The rear access door might be damaged.
- The wheels on the starwheel assembly might be damaged.
Please mark the post that solves your problem as "Accepted Solution"
(Although I am employed by HP, I am speaking for myself and not for HP)
09-26-2012 09:00 PM
What printer models is this intended for? I assume it is aimed at the lower end inkjets, with the suggestion of loading 10-25 sheets of paper.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V
04-09-2013 02:19 PM
- Using HP Diagnostic Tools for HP Printers in Windows
- Printer Problems after Upgrading to Windows 10
- Print Jobs Stuck in Print Queue (Windows)
- Resolving 'Problem with Printhead,' 'Printer Failure,' 'Ink System Failure,' or a '0x...' or a 'C2...' Error
- 'Offline' Printer Status Message Displays (Windows 10)