cancel
Showing results for 
Search instead for 
Did you mean: 
Blenks
Level 1
8 7 0 0
Message 1 of 12
476
Flag Post

162-system option not set

HP Recommended
Hp z600
Microsoft Windows 10 (64-bit)

i can't boot, it display replace the board battery, i do this the message still persist

11 REPLIES 11
Blenks
Author
Level 1
8 7 0 0
Message 2 of 12
Flag Post
HP Recommended

I already tried to press f10 key when I turn on my desktop and release it, the bios setup not appear, and message persist.

Thank you... 

Was this reply helpful? Yes No
DGroves
Level 11
4,683 4,657 440 987
Message 3 of 12
Flag Post
HP Recommended

shutdown computer

 

power on computer and immediately start tapping F10 quickly

 

continue tapping F10 key till "SETUP" msg shown in lower right, system will now enter bios after basic system checks 

Was this reply helpful? Yes No
Blenks
Author
Level 1
8 7 0 0
Message 4 of 12
Flag Post
HP Recommended

Already do this, several times but bios setup never start.

20210207_202040_Film1.jpg

Was this reply helpful? Yes No
DGroves
Level 11
4,683 4,657 440 987
Message 5 of 12
Flag Post
HP Recommended

make sure the cmos battery is a KNOWN GOOD BATTERY using a voltmeter

 

a good battery will show 2.8v anything lower is a bad battery

Was this reply helpful? Yes No
Blenks
Author
Level 1
8 7 0 0
Message 6 of 12
Flag Post
HP Recommended

I don't have a multimeter, but I put a new battery on the motherboardboar

Was this reply helpful? Yes No
DGroves
Level 11
4,683 4,657 440 987
Message 7 of 12
Flag Post
HP Recommended

no, you put a untested battery that you are assuming is good

 

error 162 is because you are either not saving the bios changes before exiting the bios or the battery/battery circuit is bad

 

Using the Computer Setup (F10) Utility to Reset CMOS

To reset CMOS using the Computer Setup (F10) Utility:
1.
Access the Computer Setup (F10) Utility menu.
 
2.
When the Computer Setup message appears in the lower-right corner of the screen, press F10,
and then press   Enter to bypass the title screen, if necessary
If you do not press  F10 while the message is displayed, the workstation must be restarted to access this utility.
 
3.
From the Computer Setup (F10) Utility menu, select File>Default Setup.
This restores the settings that include boot sequence order and other factory settings. However, it
does not force hardware rediscovery.
 
4.
Choose Restore Factory Settings as Default, and the press  F10 to accept
 
 
Was this reply helpful? Yes No
Blenks
Author
Level 1
8 7 0 0
Message 8 of 12
Flag Post
HP Recommended

I've already change the battery to a new battery, still same msg.

Was this reply helpful? Yes No
Blenks
Author
Level 1
8 7 0 0
Message 9 of 12
Flag Post
HP Recommended

When I start the pc, i press the f10 key to enter in the setup menu, but I press the f10 key it cannot enter into the setup, until give the screen above.

Was this reply helpful? Yes No
DGroves
Level 11
4,683 4,657 440 987
Message 10 of 12
Flag Post
HP Recommended

replace keyboard

Was this reply helpful? Yes No
Warning Be alert for scammers posting fake support phone numbers and/or email addresses on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation