cancel
Showing results for 
Search instead for 
Did you mean: 
chrisgreen160 Honor Student
Honor Student
2 1 0 0
Message 1 of 5
2,711
Flag Post
HP Recommended

Solved!

Trying to install more RAM in my Z420 workstation - Will not boot

HP Z420
Microsoft Windows 10 (64-bit)

So I have purchased 6 sticks of 8GB DDR3 1600mHz unbuffered RAM for my Z420 workstation. When I install the RAM the system does nto boot, and a few minuts after starting it up the fans begin to over rev, sounds like a plane taking off... not sure what to do. I have updated the BIOS to BIOS Version/Date Hewlett-Packard J61 v03.91, 10/17/2016. When I install the original 4 sitcks of 4GB RAM, the system works just fine.

4 REPLIES 4
Dean
Dean
11,617 11,017 575 1,638
Message 2 of 5
2,670
Flag Post
HP Recommended

Solved!

Trying to install more RAM in my Z420 workstation - Will not boot

> I have purchased 6 sticks of 8GB DDR3 1600mHz unbuffered RAM 

 

Your computer: https://www.support.hp.com/id-en/document/c03277050

 

Memory expansion slots - 8 DDR3 memory slots
Memory type supported - DDR3, UDIMM (Unbuffered), ECC
Memory modes - Channel interleaved
Memory speed supported - 1066-MHz, 1333-MHz, and 1600-MHz DDR3 

Maximum memory - Supports up to 64GB

 

So, your six 8GB sticks are the below the supported maximum.

 

Are you sure that you purchased 'ECC' RAM, instead of the usual "consumer" RAM?

 

Part-numbers of the original RAM?

Part-numbers of the new RAM?

 

Highlighted
Master's Graduate
Master's Graduate
336 322 20 99
Message 3 of 5
2,652
Flag Post
HP Recommended

Solved!

Trying to install more RAM in my Z420 workstation - Will not boot


@mdklassen wrote:

> I have purchased 6 sticks of 8GB DDR3 1600mHz unbuffered RAM 

 

Your computer: https://www.support.hp.com/id-en/document/c03277050

 

Memory expansion slots - 8 DDR3 memory slots
Memory type supported - DDR3, UDIMM (Unbuffered), ECC
Memory modes - Channel interleaved
Memory speed supported - 1066-MHz, 1333-MHz, and 1600-MHz DDR3 

Maximum memory - Supports up to 64GB

 

So, your six 8GB sticks are the below the supported maximum.

 

Are you sure that you purchased 'ECC' RAM, instead of the usual "consumer" RAM?

 

Part-numbers of the original RAM?

Part-numbers of the new RAM?

 


ECC REG also works fine in the Z420 - I had 64GB 1866mhz ECC Reg in mine.

There are matched kits on ebay for a very reasonable price and this would be my preferred approach to upgrading the memory in these machines.

 

chrisgreen160 Honor Student
Honor Student
2 1 0 0
Message 4 of 5
2,643
Flag Post
HP Recommended

Solved!

Trying to install more RAM in my Z420 workstation - Will not boot

Looking at the RAM, I didn't purchased ecc... well that was a stupid mistake. Thanks for the help!
Reply
0 Kudos
Dean
Dean
11,617 11,017 575 1,638
Message 5 of 5
2,630
Flag Post
HP Recommended

Solved!

Trying to install more RAM in my Z420 workstation - Will not boot

> Thanks for the help! 

 

Welcome to this forum.

 

I see that you clicked "Accept As Solution" for the SECOND person to state the requirement for 'ECC' RAM.

 

Please click the purple/white "Thumbs-Up" icon for each response that has been helpful.

 

Note that 'ECC' RAM is either "unbuffered" or "registered". 

Some motherboards that require ECC RAM can handle either type of RAM.

 

Please follow the manufacturer's specifications for your computer, and purchase "unbuffered" RAM.

Note that "unbuffered" RAM is faster than "registered" RAM.  :generic:

 

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation