fboi707 Student
Student
1 0 0 0
Message 1 of 7
803
Flag Post
HP Recommended

HP35s NONEXISTENT PROBLEM

HP35s

After finishing inputting a program into my HP35s calculator, I try to run it and it gives me nonexistent.

 

I've gone back and double checked to make sure everything was right, but it's still telling me nonexistent. any ideas?

Tags (1)
6 REPLIES 6
Distinguished Professor
Distinguished Professor
3379 3317 159 493
Message 2 of 7
768
Flag Post
HP Recommended

HP35s NONEXISTENT PROBLEM

Hi!, @Fboi707 :

Please, can you write the program what you created and see INEXISTENT ?.

You can see many programs, from ... https://www.wollindina.com/index.php/hp-calculators/hp-35s-calculator

If you needed, you can download and install the original Virtual Emulator for HP-35S, from ... https://www.educalc.net/2336231.page


You're Welcome !.
Best wishes and regards.
@Maké (Voluntary and "ad honorem").
Click the White thumb to say thanks.
Please, mark Accept As Solution if it solves your problem.
PD : The experience is like a comb. It will not do you any good, if you are bald.
Reply
0 Kudos
PhD Student
PhD Student
497 484 79 143
Message 3 of 7
756
Flag Post
HP Recommended

HP35s NONEXISTENT PROBLEM

Right after you see "Nonexistent", go into program mode, and you'll see the program step which caused the error. This usually is sufficient information to figure out what went wrong, e.g. the program might be trying to go to a label that doesn't exist.

 

Disclaimer: I don't work for HP, but I like using their programmable calculators.

-Joe-
Reply
0 Kudos
ajchin Honor Student
Honor Student
2 2 0 0
Message 4 of 7
705
Flag Post
HP Recommended

HP35s NONEXISTENT PROBLEM

Im having the same problem. i installed the closure program from here:

http://www.mygeodesy.id.au/documents/HP35s%20Surveying%20Programs.pdf

I double checked theres no error with the installation. Then I went to test and XEQ the program, it prompted me to input B (bearing) and D (degrees), after that it came up with error NONEXISTENT.  

and I went into the program again, its showing me the line C024 XEQZ015, which i am guessing theres something thats not right with this particular line? 

please advise. (i used to have the same calculator years ago but lost it, and it had no problem running the closure, now i am installing this on a new calculator and it doesnt seem to get past the nonexistent)

many many thanks

Reply
0 Kudos
Highlighted
Distinguished Professor
Distinguished Professor
3379 3317 159 493
Message 5 of 7
686
Flag Post
HP Recommended

HP35s NONEXISTENT PROBLEM

Hi!, @Ajchin :

Try, with ... C024 XEQ z015 (CF10).


You're Welcome !.
Best wishes and regards.
@Maké (Voluntary and "ad honorem").
Click the White thumb to say thanks.
Please, mark Accept As Solution if it solves your problem.
PD : The experience is like a comb. It will not do you any good, if you are bald.
Reply
0 Kudos
ajchin Honor Student
Honor Student
2 2 0 0
Message 6 of 7
588
Flag Post
HP Recommended

HP35s NONEXISTENT PROBLEM

Hi @Maké 

thanks for your reply. I have tried but couldn't input the line (CF10). How should i do it?

the C024 XEQ Z015doesnt have enough room for CF10. 

I tried CF10 on line C025, and didnt have any luck with that either. 

 

Please advice. Thanks

 

Andrew

Reply
0 Kudos
Distinguished Professor
Distinguished Professor
3379 3317 159 493
Message 7 of 7
568
Flag Post
HP Recommended

HP35s NONEXISTENT PROBLEM

Hi!, @Ajchin :

You can see, this link, where have the program and the User Guide of HP-35S, for learn, how learn edit the program ... https://issuu.com/glsense/docs/hp35s_surveying_programs


You're Welcome !.
Best wishes and regards.
@Maké (Voluntary and "ad honorem").
Click the White thumb to say thanks.
Please, mark Accept As Solution if it solves your problem.
PD : The experience is like a comb. It will not do you any good, if you are bald.
Reply
0 Kudos
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation