cancel
Showing results for 
Search instead for 
Did you mean: 
Tahir2020
New member
3 1 0 0
Message 1 of 2
141
Flag Post

HP Pavilion All-in-One - 24-xa0119 freezes a lot

HP Recommended
HP Pavilion All-in-One - 24-xa0119
Microsoft Windows 10 (64-bit)

Hi Help center, 
I bought HP Pavilion All-in-One - 24-xa0119 but the thing is it hangs a lot and it is getting annoying.  I tried to install new drivers but the issue still exists. can you help me in this matter, thanks 

 
1 REPLY 1
WAWood
Level 16
Level 16
32,773 32,673 2,975 7,303
Message 2 of 2
Flag Post
HP Recommended

@Tahir2020 

 

With a Win10 PC, you're going to experience a variety of problems not typical of the older PCs.

First is sluggishness. You may experience a very slow PC at times because Windows Update (WU) is hogging your PC, searching for, downloading, and installing updates -- to bring your PC up to the most current version of Windows. This can also contribute significantly to high processor temperatures, as it is being heavily used.

Second is fan noise. That's directly related to fan speed, which is the result of processor heat, and WU is known to drive up the processor load -- sometimes to 100%. That can cause the fan to run loud and continuous for some time.

Third is disk usage. WU can easily force the disk usage to 100% and and keep it pinned there for some time. That's because it writes WU files to the drive, then it turns around and reads them, then it overwrites existing Windows System files. All of that takes a lot of disk usage to complete.

These processes are compounded by Win10 because new Win 10 patches coming out nearly every Tuesday. Since you can't stop Updates like you did with Win7, this means you're going to get updates, regardless of what you do.

To find out what version and build of Win10 your PC is running, do the following:
1) enter "cmd" (without the quotes) into the search area and select the Command Prompt option
2) enter "winver" into the command window (again, without the quotes)
3) The most current Win10 versions as of 1/14/19 are the following:
a) v1803: Bld 17134.1184
b) v1809: Bld 17763.914
c) v1903: Bld 18632.592
d) v1909: Bld 18363.592.

If yours is older than that, most likely WU is hogging your PC trying to update it.

Some folks have been told that resetting your PC will fix this. but, if you reset your PC, you only make matters WORSE! Why? Because you will reset Win10 back to the original version that came preloaded on the PC and that will restart Windows Update all over again.

To disable WU temporarily, do the following:
1) Enter "services" in the search area (again, without the quotes)
2) When the window opens, scroll down until you see Windows Update
3) If it say Running under status, that indicates that WU is running
4) To change that, double-click on that task, select Stop under the Service status, and then Apply
5) That should stop WU -- and you should see an immediate improvement in performance.

If not, then WU is not the problem.

WU will restart itself automatically later on, so you basically have no choice than to bear with it until it finishes.

 

***If my post helped, click the thumbs-up symbol to say thanks***

***Please mark Accept As Solution if my post solved your problem***

I am a volunteer and I do not work for, nor represent, HP
0 Kudos
Warning Be alert for scammers posting fake support phone numbers and/or email addresses on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation