The HP Community is here for you.
02-04-2011 09:10 PM
I've confirmed that I indeed have the flawed Sandy Bridge Chipset as looked at the "system devices" in the device manager (i.e. I have the Intel 6 Series /C200 chipset.
Now the questiion: I have the p6780t system with one 1TB hard drive and one DVD drive. I would assume that only SATA ports 0 and 1 are used. Now from my understanding of the issue, it is the 3Gbs SATA ports from the H67/P67 chip that is problematic. Ports 0 and 1 which are the "6 Gbps" ports (but only used at 3Gbs) are OK --the reason being that the clock tree driver for the 6Gbs ports (0 and 1) are OK.
So if I never use SATA ports 2 to 5, then I would never have a problem. (Obviously, my system is limited). Appreciate anyone in the know that can respond to this. Thanks. (I'm an engineer, so you can get technical with me)
02-05-2011 05:06 PM
My advice is to not play with fire. Send the PC back. Your needs may change in the future.
HP Photosmart 6520 and HP Deskjet 1112
Custom 1151 socket Z270 Intel i7-7700k @4,600 Mhz, 16GB Corsair 3000 Mhz dimms
Corsair H75 water cooler, Corsair CS 650M power supply
RAID 0 (dual Samsung 960 EVO m.2 240GB) boot system
Dual Samsung 840 EVO SSDs 500GB data storage, Intel 750 PCIe SSD 400GB
MSI NVIDIA GTX 980TI 6GB
ASUS ROG PG279q @144 MHz
Windows 10 and Windows 8.1 Pro x64 in UEFI mode
02-08-2011 02:51 PM
You can use this utility to see what ports your SATA devices are using and the SATA level of your ports:
02-08-2011 05:05 PM
If you run that utility, please post back on which physical ports correspond to the SATA III ports - I'm sure people would find that handy, myself included.
(I have a p6780t but I can't access it until Saturday... >.< )
02-11-2011 08:37 PM
Here's the the utility report. My p6780 computer is using SATA port 2!
Note, this utility is actually for the Gigabyte MBs, so I have to do a sanity check if this is really so by openin up my box.
02-11-2011 09:24 PM
Hmm, the screen dump doesn't seem to work, but I opened the box. The hard drive is connect to SATA port 0 and the DVD drive is connect to SATA port 2. This actually makes sense. SATA port 1 is physically close to the hard disk bay, and so adding another hard drive is easily connect to port 1. For now, I'm going to leave this way, I don't use the DVD that much, and I can add another HD later.
02-12-2011 12:46 AM - edited 02-12-2011 12:52 AM
The image you tried to attach is too big for the data URI encoding thing, and it looks like cut off partway during the conversion after looking at it converted back....
On the motherboard, there isn't anything labeled SATA port 0, so I'm confused... I'm guessing you mean that the okay ports are labeled 1 and 2, but the drives are connected to 1 (HD) and 3 (DVD)? And you're going to leave the DVD drive connected to port 3?
You can always move the DVD drive at the time you need to add a second HD - the press releases make it sound like the problematic ports won't degrade as long as you avoid using them, so you might as well keep them fresh.
 Ah, I've noticed now that the ports are labeled differently on the motherboard spec page than on the physical motherboard... I guess the website's numbering is the one that should be followed.
02-12-2011 01:23 AM
The important thing to note is that the 6Gbs ports are on the side pointing outward, and the 3Gbs ports are pointing upward. On my motherboard, one "side pointing" SATA connector is connected to the HD, and the "upward-pointing" SATA connector is connected to the DVD. This makes sense because there could potentially be a very fast HD that could take advantage of the 6Gbs bandwidth, although now, my HD only operate at 3Gbs.