Ask questions. Help others.
The HP Community is here for you.
Post new question
Question
Reply
 
Note on archived topics.
This topic has been archived. Information and links in this thread may no longer be available or relevant.
If you have a question create a new topic by clicking here, or click on "Post new question" above and select the appropriate board.
Top Student
Posts: 5
Member Since: ‎07-31-2014
Message 1 of 2 (312 Views)
Accepted Solution

Opening the back cover of the hp Pavilion 23-f250 desktop all-in-one

Hi TwoPointOh

 

I appreciate letting me know step by step process of the opening the back cover of the NEW (2013) hp Pavilion 23-f250 desktop all-in-one to add ram memory. There are some video online but not for 23-f250, is there one for thins one?

 

Thanks

0 Kudos
Accepted Solution

Re: Opening the back cover of the hp Pavilion 23-f250 desktop all-in-one

Hi,

 

Try this HP Upgrade and Servicing Guide.

 

Memory Modules removal

Before you begin: Remove the VESA cover and the rear cover.

Steps

  1. Carefully pull out the EMI shield covering the memory slots – take care not to damage the battery on the motherboard.
  2. Next, gently pull out on the retaining lever located on each side of the SO-DIMM memory module.  The module will pop up from its socket.
  3. Pull the module out of the socket.

Memory Modules replacement

 

Steps

  1. There is a small notch on one side of each SO-DIMM module that fits over a small tab on one side of each SO-DIMM socket.
  2. To replace an SO-DIMM memory module, angle the module to about 45 degrees, engaging the notch into its socket tab.
  3. Press the module down into place until the retaining levers snap into position over the sides of the module.
  4. Carefully align the top edge of the EMI shield over the memory slot cutout on the motherboard shield – then press it down into place.
View solution in context
Provost
Posts: 26,600
Member Since: ‎07-17-2009
Message 2 of 2 (301 Views)

Re: Opening the back cover of the hp Pavilion 23-f250 desktop all-in-one

[ Edited ]

Hi,

 

Try this HP Upgrade and Servicing Guide.

 

Memory Modules removal

Before you begin: Remove the VESA cover and the rear cover.

Steps

  1. Carefully pull out the EMI shield covering the memory slots – take care not to damage the battery on the motherboard.
  2. Next, gently pull out on the retaining lever located on each side of the SO-DIMM memory module.  The module will pop up from its socket.
  3. Pull the module out of the socket.

Memory Modules replacement

 

Steps

  1. There is a small notch on one side of each SO-DIMM module that fits over a small tab on one side of each SO-DIMM socket.
  2. To replace an SO-DIMM memory module, angle the module to about 45 degrees, engaging the notch into its socket tab.
  3. Press the module down into place until the retaining levers snap into position over the sides of the module.
  4. Carefully align the top edge of the EMI shield over the memory slot cutout on the motherboard shield – then press it down into place.
HP laptop 17t u100,
HP Photosmart 6520 and HP Deskjet 1112
Custom 1151 socket Z270 Intel i7-7700k @4,600 Mhz, 16GB Corsair 3000 Mhz dimms
Corsair H75 water cooler, Corsair CS 650M power supply
RAID 0 (dual Samsung 960 EVO m.2 240GB) boot system
Dual Samsung 840 EVO SSDs 500GB data storage, Intel 750 PCIe SSD 400GB
MSI NVIDIA GTX 980TI 6GB
ASUS ROG PG279q @144 MHz
Windows 10 and Windows 8.1 Pro x64 in UEFI mode
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation