cancel
Showing results for 
Search instead for 
Did you mean: 
Common problems for INSTANT INK, HP+ PLANS: INK AND TONER
We would like to share some of the most frequently asked questions about Instant Ink. Check out this link: HP INSTANT INK, HP+ PLANS: INK AND TONER. .
Mkoroma
New member
1 0 0 0
Message 1 of 2
69
Flag Post

Re: Ink cartridge not recognised

HP Recommended

I'm having the similar problem with hp envy 4527 all in one printer I've done everything power cord cleaning the stripes but still nothing what do I do

1 REPLY 1
praveen196
HP Support Agent
HP Support Agent
10,488 10,491 468 739
Message 2 of 2
Flag Post
HP Recommended

@Mkoroma Welcome to HP Community!

 

I understand that the ink cartridge is not recognized.

 

Please let us know if you are using HP genuine ink cartridges.

 

Make sure the cartridge numbers match your printer and where the country/region the printer was purchased.

Go to HP Store and verify the cartridge numbers for your printer model and country/region. Replace any incompatible cartridges.

 

Please perform the hard reset and check.

 

  1. Turn the printer on, if it is not already on. 

  2. Wait until the printer is idle and silent before you continue. 

  3. With the printer turned on, disconnect the power cord from the rear of the printer. 

  4. Unplug the power cord from the wall outlet. 

  5. Wait at least 60 seconds. 

  6. Plug the power cord back into the wall outlet. 

  7. Reconnect the power cord to the rear of the printer. 

  8. Turn on the printer, if it does not automatically turn on. 

  9. Wait until the printer is idle and silent before you proceed 

Remove the cartridge indicated by the error message, clean the electrical contacts, and then reinsert the cartridge in its color-coded slot.

  1. Turn the printer on.

  2. Open the door to access the cartridges.

  3. Wait until the carriage stops moving before you continue.

  4. Remove the cartridge indicated in the error message from its slot, holding it by its side.

      caution:

    Do not touch the copper-colored contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections.

  5. Remove any protective tape that still might be on the contacts.

      caution:

    Do not touch or try to remove the copper electrical strip.

    Remove the plastic tape and do not touch the contacts or ink nozzles

  6. Lightly dampen a lint-free cloth with distilled water, and then clean only the copper-colored contacts on the cartridge.

    Cleaning the copper-colored contacts on the cartridge

  7. Lightly dampen a lint-free cloth with distilled water, and then clean the electrical contacts in the carriage, located inside the printer.

    The carriage contacts

  8. Wait 10 minutes for the contacts to dry.

  9. Reinsert the cartridge.

    • Insert the black cartridge into the right slot.

    • Insert the tri-color cartridge into the left slot.

  10. Repeat these steps for the other cartridge, if necessary.

  11. Close the cartridge access door.

  12. If the error persists, repeat the previous steps to clean the cartridge and carriage contacts a second time.

  13. Check for the error message.

If the issue still persists, please replace the ink cartridges and check for the issue.

 

Keep us posted,

If you would like to thank us for our efforts to help you, 


Give us a virtual high-five by clicking the 'Thumbs Up' icon below, followed by clicking on the "Accept as solution" on this post, 


Have a great day!

0 Kudos
Warning Be alert for scammers posting fake support phone numbers and/or email addresses on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation