cancel
Showing results for 
Search instead for 
Did you mean: 
New member
2 1 0 0
Message 1 of 5
223
Flag Post
HP Recommended

Error 0x61011beb

Asus Q505U
Microsoft Windows 10 (64-bit)

My printer is an older one, HP Photosmart C309g-m, but isn't outdated since it can still work and print wirelessly. I just haven't used it since 2015, and held onto it but secured it in safe and good condition. Fast forward a few years, now setting up a home office, I took it out to start using it again. Everything appeared to be in great condition and was dust-free. I bought new ink cartridges, but now I turned on the device and I can't even put in the new ink!

 

Everything I do, I get "General Printer Error: 0x61011beb".

 

I've looked around online and this error ironically appears to be related to ink. I open up the cartridge access door and read everywhere I looked online, "The carriage moves to the center of the printer... Wait until the carriage is idle and silent before you continue." But when I do, it goes back all the way to the right where I can't access it!

 

I went through the printer settings to clean the printhead... And it goes into the same error. I press "OK" to continue and it goes back to trying to clean the printhead and pop up with the error. I'm stuck in the cycle and have to hard reset it to go back to trying anything.

 

My laptop, like many others these days, does not have a CD drive for me to download the software that came with my printer. I tried setting up my printer with HP Smart to try to handle it that way since nothing on my printer seems to work, but after adding the printer to my network, HP Smart detects the printer and everything but says "Printer status unknown." What does that mean? Does HP Smart work with this (older) printer? I don't know if it's related or this is a separate issue, not pressing right now because I only tried downloading HP Smart to see if I can manually change the ink since automatically trying to do it won't let me.

 

What can I do?

4 REPLIES 4
Highlighted
HP Support Agent
HP Support Agent
11,578 11,569 569 622
Message 2 of 5
169
Flag Post
HP Recommended

Error 0x61011beb

@wperry

Thanks for joining HP Community!

 

I suggest you do a Hard Reset on the printer without the printer cartridge.

 

(1) Turn the printer on, if it is not already on remove the cartridge.

(2) Wait until the printer is idle and silent before you continue.

(3) With the printer turned on, disconnect the power cord from the rear of the printer.

(4) Unplug the power cord from the wall outlet.

(5) Wait at least 60 seconds.

(6) Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to the wall outlet.

(7) Reconnect the power cord to the rear of the printer.

(8) Turn on the printer, if it does not automatically turn on put the cartridge back in..

 

The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

 

Refer to this document: https://support.hp.com/us-en/product/hp-photosmart-premium-all-in-one-printer-series-c309/3984414/do...

 

Keep me posted, how it goes!

If the information provided was helpful, give us some reinforcement by clicking the Accepted Solution and Kudos buttons, that'll help us and others see that we've got the answers!

Have a great day!

Cheers:)

Raj1788
I am an HP Employee 

0 Kudos
Highlighted
New member
1 1 0 0
Message 3 of 5
123
Flag Post
HP Recommended

Error 0x61011beb

Hallo Raj

I have the same issue as described. Printer c309g, perfectly running cca 10 years, now just straight from sky error 0x61011beb.

All checked, no paper jam / debris.

What is the next step?

 

BR

Ivan

0 Kudos
Highlighted
HP Support Agent
HP Support Agent
20,464 20,452 1,356 2,017
Message 4 of 5
108
Flag Post
HP Recommended

Error 0x61011beb

@ivanEff,

 

I recommend you follow the below steps and check if it helps.

  1. With the printer turned on, disconnect the power cord from the rear of the printer and also unplug the power cord from the wall outlet. 
  2. Remove USB cable, if present. 
  3. Wait for 2-3 minutes, press and hold the power button on your printer for about 30 seconds to remove any additional charge. 
  4. Now plug back the power cable straight to a wall outlet without any surge protector or an extension cord (This is important) and then plug back the power cord to the printer. 
  5. Turn on the printer and wait till warm-up period finishes and the printer is idle.

If you continue facing the issue, then contact support as it may be a hardware issue.

 

Here is how you can get in touch with support.

1)Click on this link – www.hp.com/contacthp/

2)Select the product type.

3)Enter the serial number of your device or select let HP detect your product option.

4)Select the country from the drop-down.

5)You should see the HP phone support number or Chat option listed.

 

Cheers!

The_Fossette
I am an HP Employee

0 Kudos
Highlighted
New member
2 1 0 0
Message 5 of 5
64
Flag Post
HP Recommended

Error 0x61011beb

Hi @The_Fossette

 

I tried all the steps you did and I ended up with the same error. I unplugged everything for 5 minutes. I held the printer power button for 30 seconds. I plugged the power cable directly into a wall outlet, and then connected it to the printer. I left the USB cable disconnected. I turned on the printer, I pressed "OK" on the warning not to hard shut off a printer, and after the printer warmed up it came up with the error again.

 

I went to contact HP Support but I did not see a chat option or a phone number, the only option I could see after putting in my printer was a virtual agent, who - after being directed to confirm my device information - said my printer was out of warranty and provided me with 2 options. One to join the community and ask a question (which I did, here, already) and the second to contact HP Support (which, as before, only provided me an option for a virtual assistant).

 

Is there something else I am supposed to look for, or do I not have any more options because my printer's warranty expired?

0 Kudos
Be alert for scammers posting fake support phone numbers on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation