cancel
Showing results for 
Search instead for 
Did you mean: 
  • ×
    Information
    Fix Windows 10 Update Issues

    Resolve Windows 10 or update issues on HP computer or printer– Click Here

  • post a message
  • ×
    Information
    Fix Windows 10 Update Issues

    Resolve Windows 10 or update issues on HP computer or printer– Click Here

  • post a message
Highlighted
New member
2 1 0 0
Message 1 of 5
109
Flag Post
HP Recommended

HP OfficeJet Pro 9020 formware update fails

Officejet Pro 9020
Microsoft Windows 10 (64-bit)

Nothing the trouble with this inkjet printer. It's hooked up with a wired network and if automatic IP is set then the plotter comes with a strange IP address . If I enter a fixed IP, a day later settings gone.  ho but new firmware, ok downloaded and started and yes, the inkjet printer found, yahoo. Hmm a minute later firmware installation failed.

 

Tip if I must update the router this goes via...USB, never problems.

Not the windows firewall is not blocking the printer.

 

It has an older firmware so an update could fix network issues with the nightmare inkjet.

 So if network fails printing to this inkjet is useless..  Now that firmware update refuses for the 4 th time I don't take any actions again. , this a pro printer, sure not.  Can this device update firmware via USB in if not then it's useless and it goes to the garbage where it should have been in the first place.

 

 

4 REPLIES 4
Highlighted
New member
2 1 0 0
Message 2 of 5
97
Flag Post
HP Recommended

HP OfficeJet Pro 9020 formware update fails

I saw some info:

Please perform the hard reset and check. < my reaction

 

  1. Turn the printer on, if it is not already on.  < was on

  2. Wait until the printer is idle and silent before you continue.  < did that

  3. With the printer turned on, disconnect the power cord from the rear of the printer. <did that

  4. Unplug the power cord from the wall outlet. <did that

  5. Wait at least 60 seconds. < even longer

  6. Plug the power cord back into the wall outlet. < did that

Result still no firmware update. I start to think  that the firmware 001.1912A.00 is buggy as hell.

  1. Reconnect the power cord to the rear of the printer. 

  2. Turn on the printer, if it does not automatically turn on. 

  3. Wait until the printer is idle and silent before you proceed 

Reply
0 Kudos
Highlighted
Level 16
Level 16
27,709 27,430 4,828 10,875
Message 3 of 5
84
Flag Post
HP Recommended

HP OfficeJet Pro 9020 formware update fails

Hi,

Please connect the printer with a USB to your computer and allow it several minutes to complete the device configuration, a new printer should be added, listed as HP OfficeJet Pro 9010 series or HP OfficeJet Pro 9010 series PCL3, without any Network or letters and numbers added.

 

Download and launch below utility from your PC:

https://ftp.hp.com/pub/softlib/software13/printers/ojp9020/2010a/OJP9020_2010A.exe

 

Follow the steps on-screen by selecting the USB printer and completing the update, then unplug the USB and check for any difference.

 

Shlomi


Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution 🙂
Reply
0 Kudos
Highlighted
New member
1 1 0 0
Message 4 of 5
56
Flag Post
HP Recommended

HP OfficeJet Pro 9020 formware update fails

I have the same issue.  A brand new 9025 at F/W: MANHHIPP1N001.1914B.00 and ran the OJP9020_2010.exe on Windows 7 64-bit via USB 2 and it initiates the F/W update by automatically powering off the 9025 and then the LCD screen displays "Verifying".  Windows update app scrolls back and forth as if it's updating and then after about 15 mins, the Windows app times out and states that it failed and then you have to click the 'X" on the LCD screen on the printer to quit verifying since it never updates anything.  It then powers off and on and remains at the same F/W version.  Obviously there appears to be an issue with this release.

Reply
0 Kudos
Highlighted
Level 16
Level 16
27,709 27,430 4,828 10,875
Message 5 of 5
32
Flag Post
HP Recommended

HP OfficeJet Pro 9020 formware update fails

May you able to connect the printer to the network and update the firmware directly from the printer as listed below?

https://support.hp.com/ee-en/document/c02919168

Please let me know,

Shlomi

 

 


Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution 🙂
Reply
0 Kudos
Be alert for scammers posting fake support phone numbers on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation