cancel
Showing results for 
Search instead for 
Did you mean: 
Mart010 Top Student
Top Student
6 5 0 0
Message 1 of 10
327
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

HP Officejet 7410xi All-In-One Printer
Microsoft Windows 8.1 (64-bit)

 

This issue has been addressed before in a previous topic. Link below:

https://h30434.www3.hp.com/t5/LaserJet-Printing/HP-Officejet-7410-All-in-One-does-not-boot-anymore/t...

 

However, the reference link for resolution is no longer valid, and I've been asked to start a new thread on this.

 

Since the previous topic covers a lot of detail about the condition experienced, I'm only providing a short description here:

 

Issue:

After powering on the printer, the mini display screen that displays the HP Invent startup continously shows the progress bar without any progress ! Re-powering the printer after a while gives the exact result OR a self-reboot behavior kicks in causing the same behavior as described. This can go on for a long time without any behavioral difference.

 

Question:

Anyone here have the images from the link when it did work ? Or a more updated reference to the solution ?

 

What I've acheived so far:

- Opened the back panel of my HP All In One 7410

- Unplugged a few cables one at a time, and in combination. After each adjustment, the printer was powered on, observed and eventually shutdown on failure.

 

Any help in getting this resolved would be appreciated.

9 REPLIES 9
HP Support Agent
HP Support Agent
5,478 4,662 304 290
Message 2 of 10
299
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

Hi @Mart010,

 

A warm welcome to HP Community!

We might be able to resolve boot up issue by removing the ink cartridges and power cycling the printer. Here is how to do it:

1) Make sure this printer is plugged into a direct wall, not a surge protector

2) Remove all of your ink cartridges from the printer and close the door

3) Remove the power cord from the back of the printer (Do no press the power button)

4) Plug the power cord back into the printer

5) Wait for the printer to turn on completely, then install the ink cartridges.

Let me know how it goes!

 

If the information I've provided was helpful, give us some reinforcement by clicking the Accepted Solution and Kudos buttons, that'll help us and others see that we've got the answers!
Have a great day!

Senan6806


I am an HP Employee

Reply
0 Kudos
Mart010 Top Student
Top Student
6 5 0 0
Message 3 of 10
290
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

 

I had attempted to remove the printer ink cartridges as a first step. The catridge holder would not move (as it typically does) when a printer is turned on and the front section lifted. This is when I searched the internet and found the previous article about the rear panel. I tried this again today and, was able to lift the flaps of both the cartridge trays up - the black and the tri-color. However, I'm not able to pull the ink cartridges completely out of it owing to the obstruction right in front of it, as shown in the attached picture. I've also attached an image of the front display panel.

 

Cartridges.jpgFrontPanel.jpg

 

Reply
0 Kudos
HP Support Agent
HP Support Agent
5,478 4,662 304 290
Message 4 of 10
276
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

@Mart010

 

I believe the ink cartridge carriage should be all the way towards the right side, if it's not try manually moving the carriage all the way towards the right side and then remove the ink cartridges.

Figure : Open the cartridge latch

Open the cartridge latch

Figure : Slide out the cartridge

Slide out the cartridge

 

Keep me posted!

Senan6806


I am an HP Employee

Reply
0 Kudos
Mart010 Top Student
Top Student
6 5 0 0
Message 5 of 10
269
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

That assembly is all the way to the right. But so is that bar with the white sticker on it. If not for that, the cartridge would have slid off. I tried sliding the assembly to the left, but it won't move easily. Since it's all the way to the right, it's also hard to get a grip on the entire unit. I'm afraid to put too much pressure.

 

Btw, how is it that in the images you've attached, the white-stickered piece is not there ? Is it owing to differences in the model ? Of course, if everything was functioning correctly, that piece would have retracted somewhere, making it easy to lift the flaps and withdraw the cartridges.

Reply
0 Kudos
HP Support Agent
HP Support Agent
5,478 4,662 304 290
Message 6 of 10
258
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

@Mart010

 

I got the image from this document, is it possible to remove that plastic piece with the white sticker. It looks like that piece is not supposed to be there.

Senan6806


I am an HP Employee

Reply
0 Kudos
Mart010 Top Student
Top Student
6 5 0 0
Message 7 of 10
251
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

 

That piece has always been there. It's an extension of a tray-like structure beneath the cartridge receptacles. Under "normal" behavior, then the top half (not the lid for the scanner/copier) of the printer is lifted up for ink maintenance, the entire print head unit undergoes a change. That bottom tray with the plastic flap and white sticker retracts back OR the top-half of the print assembly elevates. Either way the 2 receptacle flaps can be "easily" lifted and the cartridges extracted. The assembly can even be slid towards the left along the designated metal rails.

 

I think it ties to the problem I'm facing. The boot-up does not complete so the whole print/ink assembly is not where it's meant to be. So any efforts near there are going to be forced.

Reply
0 Kudos
HP Support Agent
HP Support Agent
5,478 4,662 304 290
Message 8 of 10
209
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

@Mart010

 

It looks like a plastic guard moves into place blocking access to the cartridges when you turn off the product. If the guard is blocking access to the cartridge, turn the product on. It may be necessary to turn the product off and then on again to move the black guard out of the way. You may need to nudge the plastic guard softly with your finger to assist the movement.

Senan6806


I am an HP Employee

Reply
0 Kudos
Highlighted
Mart010 Top Student
Top Student
6 5 0 0
Message 9 of 10
187
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

After several power cycles with and without the front section (that allows access to the print assembly) lifted, I don't see any movement of that assembly. Nothing moves when the power is turned on.

Reply
0 Kudos
HP Support Agent
HP Support Agent
5,478 4,662 304 290
Message 10 of 10
183
Flag Post
HP Recommended

HP Officejet 7410 All-in-One: Hangs during bootup

@Mart010

 

I'm afraid, it's a possible hardware failure and the printer needs to be serviced/replaced. Please contact your regional HP Support to obtain all available service/replacement options. You may reach them from here

Senan6806


I am an HP Employee

Reply
0 Kudos
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation