cancel
Showing results for 
Search instead for 
Did you mean: 
jimbowags
New member
2 0 0 0
Message 1 of 3
71
Flag Post
HP Recommended

Printer Failure

HPofficejet 6600

Installed non HP cartridges----printer stopped working. Ordered and installed HP cartridges----printer still doesn't work. .Get a ,essags "there is a problem with the printer or ink system" " turn printer off than on . If  problem persists, contact HPOx61011bed"

2 REPLIES 2
HP Support Agent
HP Support Agent
2,157 2,157 98 175
Message 2 of 3
30
Flag Post
HP Recommended

Printer Failure

@jimbowags Welcome to HP Community!

 

I understand that you are getting an ink system failure. 

 

I would like to help you resolve this issue. 

 

However, I will need a few details to provide an accurate solution,

When did this issue start?

Did you do any hardware or software changes?

How is the printer connected to a computer, wired or wireless?

 

Meanwhile               

Reset the printer

  1. Turn the printer on, if it is not already on.

  2. Wait until the printer is idle and silent before you continue.

  3. With the printer turned on, disconnect the power cord from the rear of the printer.

  4. Unplug the power cord from the wall outlet.

  5. Wait at least 60 seconds.

  6. Plug the power cord back into the wall outlet.

      note:

    HP recommends connecting the printer power cord directly to the wall outlet.

  7. Reconnect the power cord to the rear of the printer.

  8. Turn on the printer, if it does not automatically turn on.

    The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

  9. Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

Clean the ink cartridges, and then check the error message

  1. Gather the following materials:

    • A clean, lint-free cloth or a clean, dry cotton swab

    • Distilled or bottled water

        caution:

      Do not use tap water because it might contain contaminants that can damage the printhead.

  2. Lightly dampen a clean, lint-free cloth with bottled or distilled water.

  3. Gently wipe the copper-colored contact on one of the ink cartridges.

    Figure : Example of copper-colored contact

    Example of copper-colored contact
  4. Wipe the contact with a dry, lint-free cloth before proceeding to the next step.

  5. Repeat these steps for the three remaining ink cartridges.

  6. Carefully reinsert each of the ink cartridges into its slot, and then push the ink cartridge down and forward until it clicks into place.

    Figure : Reinserting the ink cartridge

    Reinserting the ink cartridge
  7. Make sure each colored dot on the ink cartridge label matches the colored dot on the print carriage.

    Figure : Matching the colored dot on the print carriage

    Matching the colored dot on the print carriage
  8. From the home screen on the printer control panel, touch the HP ePrint icon .

  9. Wait for the printer to connect to the HP ePrint server.

    When the printer connects to the server, the HP ePrint status displays.

  10. Touch Settings on the bottom left corner of the screen.

  11. Touch Printer Update, and then touch Check for Update Now.

Reseat the printhead up to three times

  1. Slip your fingers into the slot on the left side of the printer, and then pull forward to open the cartridge access door. The carriage moves to the left side of the printer. Wait until the carriage is idle and silent before proceeding.

    Figure : Open the cartridge access door

    1. Slot on the left side of the printer

  2. Unplug the power cord from the rear of the printer. Unplugging the printer prevents the carriage from moving.

      warning:

    You must disconnect the power cord before reaching inside the printer to avoid risk of injuries or electric shock.

  3. Lift the carriage latch.

    Figure : Lift the carriage latch

    Image: Lift the carriage latch.
  4. Grasp the sides of the printhead, and then slightly lift the printhead without fully removing it from the carriage.

    Figure : Slightly lift the printhead

    Image: Slightly lift the printhead.
  5. Reinsert the printhead into the carriage to reseat it. As you guide the printhead into the carriage, it lowers into the carriage as it seats.

    Figure : Reseat the printhead

    Image: Reseat the printhead.
  6. Gently rock the printhead to the left and right to make sure that the printhead fully seats in the carriage.

  7. Lower the carriage latch.

    Figure : Lower the carriage latch

    Image: Lower the carriage latch.
  8. Verify that the carriage latch is down.

    Figure : Carriage latch positions

    1. Carriage latch is up

    2. Carriage latch is down

  9. Close the cartridge access door.

  10. Reconnect the power cord to the rear of the printer.

  11. If the printer does not turn on by itself, press the Power button to turn it on.

  12. Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

Update the printer firmware

  1. From the home screen on the printer control panel, touch the HP ePrint icon .

  2. Wait for the printer to connect to the HP ePrint server.

    When the printer connects to the server, the HP ePrint status displays.

  3. Touch Settings on the bottom left corner of the screen.

  4. Touch Printer Update, and then touch Check for Update Now.

Click here and refer to the HP Document for more assistance.

 

Keep us posted,

If you would like to thank us for our efforts to help you, 


Give us a virtual high-five by clicking the 'Thumbs Up' icon below, followed by clicking on the "Accept as solution" on this post, 


Have a great day!

 

Reply
0 Kudos
HP Support Agent
HP Support Agent
2,157 2,157 98 175
Message 3 of 3
21
Flag Post
HP Recommended

Printer Failure

@jimbowags

 

We haven't heard from you in a while,
This post is with reference to the thread you had created at your friendly neighborhood (HP Community),
 
I would like to know if the resolution we had provided worked for you?
Please reply to your public post as we like to encourage our community to grow
 
If you have any other queries, feel free to reply at any time,
And thank you for being a valuable member of our HP Family.
 
If you would like to thank us for our efforts to help you, 
Go to the public post & give us a virtual high-five by clicking the 'Thumbs Up' icon below, followed by clicking on the "Accept as solution" on the post you feel, helped you the most, 
Have a great day!

Reply
0 Kudos
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation