cancel
Max50 Tutor
Tutor
10 7 1 1
Message 1 of 3
128
Flag Post
HP Recommended

Solved!

Printer J4680 disconects when adding scanned pages. Connected wireless and using Windows 7

Officejet j4680
Microsoft Windows 7 (64-bit)

The printer losing connection when scanning a document in PDF an try to add additional pages.

 

Askedto start from the begining.

 

Loaed the software, reset printer,loaded upated driver, done it four times, otherwie works ok.

2 REPLIES 2
Provost
Provost
20,763 20,455 1,537 3,411
Message 2 of 3
117
Flag Post
HP Recommended

Solved!

Printer J4680 disconects when adding scanned pages. Connected wireless and using Windows 7

These settings are for setting up your wireless or wired printers to:

* Stay connected to your router
* Fix printer ‘offline’ status
* Wake from sleep mode
* Speed up wireless printing

While DHCP is convenient, devices such as printers (wired and wireless) should always be assigned a static (fixed) IP address manually to avoid conflicts on your wireless network and MUST be outside the DHCP range of the router. This is because printers are the only external devices that do not have the power to automatically interrupt the router for a new DHCP address once the least time expires.  

After setting the static IP, the computer(s) must be updated under Printer Properties/Ports to show a Standard TCP/IP port with the printers’ new static IP address.

1. Set a static IP in the printer outside the DHCP range of the router (check your manual).  This static IP is important as DHCP IP addresses will change upon different power up sequences of your devices.  You always want your printer to come up with the same IP address all the time.  See how to do this here:

http://www.watchingthenet.com/linksys-tip-assign-static-ip-address-to-printer-while-using-dhcp-on-yo...

This is for Linksys routers but can be used for all routers. Verify your DHCP range and change this first if needed.  After setting the static IP, the computer(s) must be updated under Printer Properties/Ports to show a Standard TCP/IP port with the printers IP address.  

To see why this problem exists and how to fix it, watch this video here for Windows.   Scroll down for MAC information.

https://www.youtube.com/watch?v=ZEqvUKxWmq4

How to set a Standard TCP/IP port.  This is important.

a.    Click Start/Devices and Printers.  Right click on your HP Printer.  Select Printer Properties.  Select the Ports tab at the top.
b.    Select Add Port.  Select Standard TCP/IP Port.  Select New Port.
c.    Follow the Add Port Wizard.  Under Printer Name or IP Address, input the Static IP address you just set from the above information.  Example:  192.168.1.15.  The IP address will be copied under Port Name.  This is OK to leave this alone or you can put in your Printer Model.
d.    Select Next and Finish the Wizard.

If you create a TCP/IP port without a static IP above, you may lose your TCP/IP connection and have the same issue. This is because your network has powered up differently giving you a different DHCP address to the printer that does not match the TCP/IP address above.  This could occur at anytime just like the video shows.

For MAC PCs perform the above Static IP setting in the router and then watch here on how to perform your IP setting for MAC computers.

https://www.youtube.com/watch?v=A5tNFjEBDOw

By performing the above, the printers Embedded Web Server (EWS) will now work all the time by going to your Static IP address in your browser.  

2. Verify in the printer that 'Auto Off/Sleep/Energy Saving Mode' is disabled and/or the System Mode Time Out is set to zero (0).  Use the Embedded Web Server (EWS) by going to the printers IP address in your browsers address bar, click Settings Tab/Auto Off, or use the Printer Assistant, Printer Home Page (EWS). Also check your Printer Properties.

3. If the printer supports and has IPv6 enabled, disable IPv6 in the printer.

4. Make sure printer is plugged directly into a wall outlet and not into a UPS, power strip or surge protector. This will cause the printer to drop offline and disconnect (yes verified!).

5.  Make sure your printer and router are at least 5 feet apart from each other.

Additional steps to be taken if you continue to have the problem (if they are posted)…

Click on the link to subscribe and get the latest video uploads: https://goo.gl/y4Rcn1 This tutorial shows how to add a printer using the IP address for macOS 10.12 Sierra. The added printer is sometimes more stable and also helps to resolve some print and scan issues such printer offline. HP ...
Printer offline issues can happen because the IP address of the printer keeps changing. This video explains how that can happen and what to do to fix it. For more tech tips, check out http://www.linearthoughts.co.uk .
Max50 Tutor
Tutor
10 7 1 1
Message 3 of 3
87
Flag Post
HP Recommended

Solved!

Printer J4680 disconects when adding scanned pages. Connected wireless and using Windows 7

Thanks for th reply that partaly helped.

 

Onc you said that I needed a static IP.  besdes creatig the new port I hd to log in the HP J4680 old IP disable he DHCP and enter a staic IP in the pinter.

 

That together with the new port created the functioning new static prnter.

 

As a mater of fact, once you go into the printer and set up the static IP, you can ask for an new printer "add a printer" and will work.

 

The pont of staic IP was the solution.

 

Te HP sftware sucks.

Reply
0 Kudos
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation