Laserjet M203dw does not wake up after going to sleep mode

[gurusql]

We have a Laserjet M203dw that goes into power saving mode and will not wake up when it recieves a print job. The user must turn the printer off and on again to get it to print.

Connection Method - Wireless

Main status light (on the power button) is off and must be manually powered on. The wireless only this connects sometimes, requiring the wireless button to be held down.

Any suggestions?

[sabretooth04]

These settings are for setting up your wireless or wired printers to:

* Stay connected to your router
* Fix printer ‘offline’ status
* Wake from sleep mode
* Speed up wireless printing

While DHCP is convenient, devices such as printers (wired and wireless) should always be assigned a static (fixed) IP address manually to avoid conflicts on your wireless network and MUST be outside the DHCP address range of the router. This is because printers are the only external devices that do not have the ability to automatically interrupt the router for a new DHCP address once the least time expires.  Again, do not have the printers static IP within the DHCP range of the router as this is against Networking 101 rules and will confuse the router.  Make things simple – In the router, set starting DHCP address range 192.168.1.100 (or 192.168.0.100). Ending DHCP address range 192.168.1.150 (or 192.168.0.150).  Set Printer Static IP to 192.168.1.10 (or 192.168.0.10).  

After setting the static IP, the computer(s) must be updated under Printer Properties/Ports to show a Standard TCP/IP port with the printers’ new static IP address.

1. Set a static IP in the printer outside the DHCP range of the router (check your manual).  This Static IP is important as DHCP IP addresses will change upon different power up sequences of your devices.  You always want your printer to come up with the same IP address all the time.  See how to do this here:

http://www.watchingthenet.com/linksys-tip-assign-static-ip-address-to-printer-while-using-dhcp-on-yo...

This is for Linksys routers but can be used for all routers. Verify your DHCP range and change this first if needed.  Then after setting the static IP in the printer, the computer(s) must be updated under Printer Properties/Ports to show a Standard TCP/IP port with the printers IP address.  

To see why this problem exists and how to fix it, watch this video here for Windows.   Scroll down for MAC information.

https://www.youtube.com/watch?v=ZEqvUKxWmq4

How to set a Standard TCP/IP port.  This is important.

a.    Click Start/Devices and Printers.  Right click on your HP Printer.  Select Printer Properties.  Select the Ports tab at the top.
b.    Select Add Port.  Select Standard TCP/IP Port.  Select New Port.
c.    Follow the Add Port Wizard.  Under Printer Name or IP Address, input the Static IP address you just set from the above information.  Example:  192.168.1.15.  The IP address will be copied under Port Name.  This is OK to leave this alone or you can put in your Printer Model.
d.    Select Next and Finish the Wizard.

If you create a TCP/IP port without a static IP above, you may lose your TCP/IP connection and have the same issue. This is because your network has powered up differently giving you a different DHCP address to the printer that does not match the TCP/IP address above.  This could occur at anytime just like the video shows.

For MAC PCs perform the above Static IP setting in the router and then watch here on how to perform your IP setting for MAC computers.

https://www.youtube.com/watch?v=A5tNFjEBDOw

By performing the above, the printers Embedded Web Server (EWS) will now work all the time by going to your Printers Static IP address in your browser.  

2. Verify in the printer that 'Auto Off/Sleep/Energy Saving Mode' is disabled and/or the System Mode Time Out is set to zero (0) if your printer supports this.  Use the Embedded Web Server (EWS) by going to the printers IP address in your browsers address bar, click Settings Tab/Auto Off, or use the Printer Assistant, Printer Home Page (EWS). Also check your Printer Properties. This feature is automatically disabled when the printer is connected to a computer or mobile device, a network, or a fax line (if supported).   However, you may not find this setting.

3. If the printer supports and has IPv6 enabled, disable IPv6 in the printer.

4. Make sure printer is plugged directly into a wall outlet and not into a UPS, power strip or surge protector. This may cause the printer to intermittently drop offline and disconnect.

5.  Make sure your printer and router are at least 5 feet apart from each other.

6.  Check the HP web site for your printer to see if there is a Firmware Upgrade that affects the wireless operation.  If yes, update the firmware via USB cable only.  Never wireless.

Additional steps to be taken if you continue to have the problem (if they are posted)…

[mevansecs]

I have the same issue with 3 Laserjets we purchased last month.  We have 150 other devices that don't have an issue with our network so those instructions are worthless to people.  All 3 printers go to sleep and don't wake up when a job is sent.  HP says the sleep option can't be turned off.  So my options are to turn off/on to get them to wor.  I don't underrstand why HP puts their customers through this stuff.

[CooChar]

I am having the same problem. I am like you and do not understand why HP did this. I am going to be purchasing a new printer this week and it will not be an HP.

[Cheron-Z]

@CooChar

Thank you for posting in this thread. Unfortunately based on when the last response was made, I have closed this thread to help keep comments current and up to date. We recommend starting a new thread for your issue by clicking here.
To be more helpful with your post, you can add key information if you desire: 
1. Product Name and Number (please do not post Serial Number)
• Example: HP Pavilion DV2-1209AX or HP Deskjet 3000 Printer CH393A
2. Operating System installed (if applicable)
• Example: Windows XP, Windows Vista 32-bit, Windows 7 64-bit
3. Error message (if any)
• Example: ""Low disk space"" error in Windows
4. Any changes made to your system before the issue occurred
• Examples: Upgrading your Operating System or installing a new software; or installing new hardware like a printer, modem, or router.
If you have any other questions about posting in the community, please feel free to send me a private message!

Thank you