• ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
We are proud to announce new Poly Studio Series video bars and remote room control with Poly Connect. Read more about the solutions!
Locked

‎10-28-2014 10:10 AM

HP Recommended

I'm getting the following error on a couple HDX4000 endpoints trying to update from 3..01: to 3.1.3.2..

Error is : “Monitor camera check FAILED. Please secure monitor cables and restart software upgrade." we cannot change camera or monitor settings in this devcie to get around error in order to update endpoint. . Does anyone have any tips or tricks please?  I'm not finding this error posted here.  Thanks .

3 REPLIES 3

‎10-28-2014 12:49 PM

HP Recommended

Hello JoeBMplsMN,

welcome to the Polycom Community.

  • Have you tried to go to a later 3.0.x software first and then to a 3.1.x ?

  • Do you have the relevant license to upgrade to this software ?
     
  • Is there a specific reason going to 3.1.3.2 instead to 3.1.5 directly ?

  • Did you check the release notes Hardware and Software Compatibility  section if yoru HDX part number is compatible ?


Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.

Best Regards

Steffen Baier

Polycom Global Services

------------------------------------------------
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.

Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN
Was this reply helpful? Yes No

‎10-28-2014 05:10 PM

HP Recommended

Make sure the cable is secure (screwed down) between the dispaly and the codec. Make sure the cable is connected to both the HDCI input and the monitor output (which I am sure it is as you are seeing the output).

Was this reply helpful? Yes No

‎10-29-2014 07:45 AM

HP Recommended

Hi Steffen, Thanks for the response.  

 

  • Have you tried to go to a later 3.0.x software first and then to a 3.1.x ? no, but willing to try anything.

  • Do you have the relevant license to upgrade to this software ? Yes 
     
  • Is there a specific reason going to 3.1.3.2 instead to 3.1.5 directly ? The clients infrastructure has not tested/approved that version  . But I feel the lates t versions are typicaly already tested and addressed prior issues.

  • Did you check the release notes Hardware and Software Compatibility  section if yoru HDX part number is compatible ?Yes it was listed.

 

I"ve recieved a Polycom Article ID 14525: Monitor Camera Check fail" error during update.  with the codec powered ON , disconnect the monitor cable and then the power cable.  wait a few moments. Replace power cord , push the power button and then reconnect monitor cable - basically perform a hot swap of the cable.  re run software update.

 

I will keep you posted of the results. once able to update.    

 

Was this reply helpful? Yes No
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.
Didn't find what you were looking for? Ask the community
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.