cancel
Showing results for 
Search instead for 
Did you mean: 
Pards
New member
1 0 0 0
Message 1 of 4
3,723
Flag Post

Error code 0x61011bed

HP Recommended
HP Officejet 6600

Hi Can anyone help resove error code 0x61011bed

3 REPLIES 3
Riddle_Decipher
HP Support Agent
HP Support Agent
31,166 31,117 2,618 3,994
Message 2 of 4
Flag Post
HP Recommended

 

@Pards

Welcome to HP Forums,

Let's get straight to it!

 

Have you attempted to reset the printer?

If not, please ensure you are using genuine HP ink cartridges and then, let's start with the reset:

In some cases, a printer reset can clear the error message.

  1. Turn the printer on, if it is not already on.

  2. Wait until the printer is idle and silent before you continue.

  3. With the printer turned on, disconnect the power cord from the rear of the printer.

  4. Unplug the power cord from the wall outlet.

  5. Wait at least 60 seconds.

  6. Plug the power cord back into the wall outlet.

       NOTE:

    HP recommends connecting the printer power cord directly to the wall outlet.

  7. Reconnect the power cord to the rear of the printer.

  8. Turn on the printer, if it does not automatically turn on.

  9. Wait until the printer is idle and silent before you proceed.

If the issue persists, continue to the next step.

 

Step 3: Remove the ink cartridges

Removing the ink cartridges and checking for an error message can help diagnose the printer issue. Take the ink cartridges out of the printhead, and then check the printer control panel or computer for an error message.

  1. Open the ink cartridge access door.

    The carriage moves to the left side of the access area.

  2. Wait until the carriage is idle and silent before proceeding.

  3. Push in on the front of one of the ink cartridges to release it, and then pull the ink cartridge toward you to remove it.

    Figure : Removing the ink cartridge

    Removing the ink cartridge
  4. Repeat these steps for the other ink cartridges.

  5. Close the ink cartridge access door.

  6. Check the control panel to see if an error message displays.

    • If the printer displays an Ink System Failure message on the control panel, skip to the step to Update the printer firmware.

    • If the message has changed to Replace the, or Ink Cartridge, continue to the next step.

FOR DETAILS & FURTHER INSTRUCTIONS, USE THIS LINK: CLICK HERE & SKIP TO STEP 4 ONWARD

(By the end of this article all the issues should be resolved)

 

Let me know how that pans out,

If you feel I was helpful, simply click on Accept as Solution to help the community grow,

That said, I will have someone follow-up on this to ensure you've been helped,

Just in case you don't get back to us within 24 - 48hrs, and have a good day, ahead.

Riddle_Decipher
I am an HP Employee

0 Kudos
MarcMe
New member
1 1 0 0
Message 3 of 4
Flag Post
HP Recommended

I tried all suggestions. nothing works. However I cannot update firmware as HP does not support the HP7510 printer anymore.: the printer cannot get access to the Webservices. The question changes now: how can I update my HP7510 printer. 

0 Kudos
Surffossil
New member
1 1 0 0
Message 4 of 4
Flag Post
HP Recommended

This did not help as both of the links (in the solution) are dead.  Any other solution other than the round file...?

0 Kudos
Warning Be alert for scammers posting fake support phone numbers and/or email addresses on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation