cancel
Showing results for 
Search instead for 
Did you mean: 
  • ×
    Information
    Need Windows 11 help?
    Check documents and videos on compatibility, FAQs, upgrade information and available fixes.Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents and videos on compatibility, FAQs, upgrade information and available fixes.Windows 11 Support Center.
  • post a message
The HP Calculator Community Message Board is moving. While we prepare for the move, we are unable to accept new postings. During the move, you can look for help from other users by visiting https://www.hpmuseum.org/ . Or if you need technical support for your calculator visit: HP Calculators. .
gwc28
New member
4 2 0 0
Message 1 of 6
147
Flag Post

While the display is blank, press the f10 key to enter the BIOS settings menu. ?

HP Recommended
Paviilion 15-cs 3006na
Microsoft Windows 10 (64-bit)

I want to change boot order but F10 does not work on this Laptop. To Boot from USB. Tried F2 & F6 & F12

While the display is blank, press the f10 key to enter the BIOS settings menu.

 

Thank you gwc28

5 REPLIES 5
TheOldMan
Level 15
Level 15
11,126 8,021 1,036 2,610
Message 2 of 6
Flag Post
HP Recommended

Trying to get into the setup screen is tricky.  Try this

Start tapping the Esc key and then press the start button.
Keep tapping the Esc key until a popup menu shows. You can then pick F10 to enter the setup menu

 


I'm not an HP employee.
Did this message answer your question? Please indicate below as an Accepted Solution!
Did you find this message useful? Click on the thumbs up to give Kudos! " >.

Was this reply helpful? Yes No
gwc28
Author
New member
4 2 0 0
Message 3 of 6
Flag Post
HP Recommended

Reply Appreciated but unfortuately this did NOT get me into changing the Boot Order.

Was this reply helpful? Yes No
TheOldMan
Level 15
Level 15
11,126 8,021 1,036 2,610
Message 4 of 6
Flag Post
HP Recommended

Did you get the popup menu that should show up to get to F10?

Start tapping the Esc key Before turning on the computer and then keep tapping after the start button is pressed until the popup menu shows.


I'm not an HP employee.
Did this message answer your question? Please indicate below as an Accepted Solution!
Did you find this message useful? Click on the thumbs up to give Kudos! " >.

Was this reply helpful? Yes No
gwc28
Author
New member
4 2 0 0
Message 5 of 6
Flag Post
HP Recommended

Start tapping the Esc key Before turning on the computer and then keep tapping after the start button is pressed until the popup menu shows.

YES, Esc Key before Start Button does WORK...Appreciated     gwc28

Was this reply helpful? Yes No
TheOldMan
Level 15
Level 15
11,126 8,021 1,036 2,610
Message 6 of 6
Flag Post
HP Recommended

Great!

So I assume that you were able to change the boot settings and use the USB?


I'm not an HP employee.
Did this message answer your question? Please indicate below as an Accepted Solution!
Did you find this message useful? Click on the thumbs up to give Kudos! " >.

Was this reply helpful? Yes No
Warning Be alert for scammers posting fake support phone numbers and/or email addresses on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation