-
×InformationWindows update impacting certain printer icons and names. Microsoft is working on a solution.
Click here to learn moreInformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center.
-
×InformationWindows update impacting certain printer icons and names. Microsoft is working on a solution.
Click here to learn moreInformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center.
- HP Community
- Printers
- Printer Setup, Software & Drivers
- Set which network access point my HP8600 connects to wireles...
Create an account on the HP Community to personalize your profile and ask a question
05-02-2017 02:19 PM
I have 2 wireless network access points close to my HP8600 printer (my main wireless router, and an additional access point router). They both have the same SSID and security key. This seems to make my printer constantly lose connection. Is there a fix? Can I set permanently which router I want the printer to connect to?
Solved! Go to Solution.
Accepted Solutions
05-02-2017 03:46 PM
OK, this is going to be a little tough. HP printers don't play well with multiple access points. However there are some things that can help.
First you have 2 access points. You need to have 1 set to channel 1, the other set to channel 6 or channel 11. This is for seamless roaming. Same SSID and password are fine.
With that said, place the printer closest to the access point with channel 1 selected. Very important.
Next you need to perform the following...
These settings are for setting up your wireless or wired printers to:
* Stay connected to your router
* Fix printer ‘offline’ status
* Wake from sleep mode
* Speed up wireless printing
While DHCP is convenient, devices such as printers (wired and wireless) should always be assigned a static (fixed) IP address manually to avoid conflicts on your wireless network and must be outside the DHCP range of the router. This is because printers are the only external devices that do not have the power to automatically interrupt the router for a new DHCP address once the least time expires.
After setting the static IP, the computer(s) must be updated under Printer Properties/Ports to show a Standard TCP/IP port with the printers’ new static IP address.
1. Set a static IP in the printer outside the DHCP range of the router (check your manual). This static IP is important as DHCP IP addresses will change upon different power up sequences of your devices. You always want your printer to come up with the same IP address all the time. See how to do this here:
http://www.watchingthenet.com/linksys-tip-assign-static-ip-address-to-printer-while-using-dhcp-on-yo...
This is for Linksys routers but can be used for all routers. Verify your DHCP range and change this first if needed. After setting the static IP, the computer(s) must be updated under Printer Properties/Ports to show a Standard TCP/IP port with the printers IP address.
To see why this problem exists and how to fix it, watch this video here:
https://www.youtube.com/watch?v=ZEqvUKxWmq4
How to set a Standard TCP/IP port. This is important.
a. Click Start/Devices and Printers. Right click on your HP Printer. Select Printer Properties. Select the Ports tab at the top.
b. Select Add Port. Select Standard TCP/IP Port. Select New Port.
c. Follow the Add Port Wizard. Under Printer Name or IP Address, input the Static IP address you just set from the above information. Example: 192.168.1.15. The IP address will be copied under Port Name. This is OK to leave this alone.
d. Select Next and Finish the Wizard.
By performing the above, the printers Embedded Web Server (EWS) will now work all the time by going to your Static IP address in your browser also.
2. Verify in the printer that 'Auto Off/Sleep/Energy Saving Mode' is disabled and/or the System Mode Time Out is set to zero (0). Use the Embedded Web Server (EWS) by going to the printers IP address in your browsers address bar, click Settings Tab/Auto Off, or use the Printer Assistant, Printer Home Page (EWS). Also check your Printer Properties.
3. If the printer supports and has IPv6 enabled, disable IPv6 in the printer.
4. Make sure printer is plugged directly into a wall outlet and not into a UPS, power strip or surge protector. This will cause the printer to drop offline and disconnect (yes verified!).
5. Make sure your printer and router are at least 5 feet apart from each other.
Additional steps to be taken if you continue to have the problem (if they are posted)…
05-02-2017 03:46 PM
OK, this is going to be a little tough. HP printers don't play well with multiple access points. However there are some things that can help.
First you have 2 access points. You need to have 1 set to channel 1, the other set to channel 6 or channel 11. This is for seamless roaming. Same SSID and password are fine.
With that said, place the printer closest to the access point with channel 1 selected. Very important.
Next you need to perform the following...
These settings are for setting up your wireless or wired printers to:
* Stay connected to your router
* Fix printer ‘offline’ status
* Wake from sleep mode
* Speed up wireless printing
While DHCP is convenient, devices such as printers (wired and wireless) should always be assigned a static (fixed) IP address manually to avoid conflicts on your wireless network and must be outside the DHCP range of the router. This is because printers are the only external devices that do not have the power to automatically interrupt the router for a new DHCP address once the least time expires.
After setting the static IP, the computer(s) must be updated under Printer Properties/Ports to show a Standard TCP/IP port with the printers’ new static IP address.
1. Set a static IP in the printer outside the DHCP range of the router (check your manual). This static IP is important as DHCP IP addresses will change upon different power up sequences of your devices. You always want your printer to come up with the same IP address all the time. See how to do this here:
http://www.watchingthenet.com/linksys-tip-assign-static-ip-address-to-printer-while-using-dhcp-on-yo...
This is for Linksys routers but can be used for all routers. Verify your DHCP range and change this first if needed. After setting the static IP, the computer(s) must be updated under Printer Properties/Ports to show a Standard TCP/IP port with the printers IP address.
To see why this problem exists and how to fix it, watch this video here:
https://www.youtube.com/watch?v=ZEqvUKxWmq4
How to set a Standard TCP/IP port. This is important.
a. Click Start/Devices and Printers. Right click on your HP Printer. Select Printer Properties. Select the Ports tab at the top.
b. Select Add Port. Select Standard TCP/IP Port. Select New Port.
c. Follow the Add Port Wizard. Under Printer Name or IP Address, input the Static IP address you just set from the above information. Example: 192.168.1.15. The IP address will be copied under Port Name. This is OK to leave this alone.
d. Select Next and Finish the Wizard.
By performing the above, the printers Embedded Web Server (EWS) will now work all the time by going to your Static IP address in your browser also.
2. Verify in the printer that 'Auto Off/Sleep/Energy Saving Mode' is disabled and/or the System Mode Time Out is set to zero (0). Use the Embedded Web Server (EWS) by going to the printers IP address in your browsers address bar, click Settings Tab/Auto Off, or use the Printer Assistant, Printer Home Page (EWS). Also check your Printer Properties.
3. If the printer supports and has IPv6 enabled, disable IPv6 in the printer.
4. Make sure printer is plugged directly into a wall outlet and not into a UPS, power strip or surge protector. This will cause the printer to drop offline and disconnect (yes verified!).
5. Make sure your printer and router are at least 5 feet apart from each other.
Additional steps to be taken if you continue to have the problem (if they are posted)…
Didn't find what you were looking for? Ask the community