The HP Community is here for you.
03-08-2012 06:45 PM
I have officejet 8600 and belkin wireless network. I have an IMAC and powerbook both running snow leopard. the belkin is new. When I changed to the Belkin I began having problems with the 8600 going offline after printing or just sitting idle for too long.
03-12-2012 04:57 PM - last edited on 02-21-2017 05:18 PM by OscarFuentes
Sorry that you are having this issue.
This tool should help;
Also look at this article
Windows 10: http://support.hp.com/us-en/document/c04249080
Windows Vista: http://support.hp.com/us-en/document/c04249080
Hope it helps;
07-08-2012 12:01 PM
This is a common issue with DHCP and certain routers. Until HP can include a "keep alive" setting, when the printer goes on "Energy Save Mode", in order to save power, it disconnects from the network and the DHCP server on your router times out the lease as it basically sees it as having been powered off.
Without doing some network diagnostics, I imagine HP engineers did not put the DHCP request to obtain the lease again, upon coming out of Energy Save Mode -- of which it likely wouldn't if you printed to the network connected printer as the OS thinks the printer is offline -- the only recourse would be to press the power button physically on the printer.
The "workaround" is to set a reserved DHCP lease for your printer on your router AND manually set a static IP address in the printer. Other potential work arounds would be to see if there are any settings on your router OR have HP address the issue with a firmware update.
07-09-2012 02:42 PM - edited 07-09-2012 02:46 PM
Hi Hobbzilla you are right,
For those who may need help with issue follow this steps and this should help;
Set an static ip address for my printer and change the DNS servers provided by your ISP to Google DNS servers
How to set an static IP address
Follow these steps to assign an unchanging static IP address to the product through the Embedded Web Server (EWS).
Open a new Web browser window.
Type the IP address located on the Network Configuration Page in the address bar of the Web browser, using http:// to begin the address e.g. http://192.168.0.1 Then press Enter . The EWS home page for the product opens.
In the EWS screen, click the Network tab.
Click Wired (802.3) , and then click the IPv4 Configuration or the IPv6 Configuration tab.
Click Manual IP . The Manual IP Address box opens.
In the Manual IP Address box, type an IP address with the same values in the first three sets of digits (subnet values) as the product's IP address (listed on the Network Configuration Page), and a higher value (between 1 and 254) in the fourth set of digits. This creates a static IP address on the same subnet, but outside the Dynamic Host Configuration Protocol (DHCP) range.
For example, if the product's original IP address is 192.168.0.1 , assign the static IP address to 192.168.0.200 .
Do not type the static IP address use as the example. Enter a static IP address based on the IP address for your product. This can be found on network configuration page.
Enter the Subnet Mask and the Default Gateway settings as they appear on the Network Configuration Page.
While you are here in the IPV4 you can set the DNS servers of google instead of the DNS servers provided by your ISP just change the option of automaticly select DNS server and use this; DNS servers of google are 22.214.171.124 and alternative DNS 126.96.36.199
Click OK to save the new settings, and then click Exit or close the browser to exit the EWS.
Make sure that the operating system is updated, that the routers firware is the lastest.
Hope this is helpful to all of you having this or a similar issues.
09-12-2012 04:36 PM
I have tried the steps outlined and the printer still goes offline.
- Turning the printer on/off
- Reinstalling the printer
- Restarting the computer
The only solution seems to be to use the USB cable. I am using a MacBook Pro, running 10.6.8.
09-12-2012 05:14 PM
I turned off the scan to computer, and the show ink level always, and the problem went away. This is a problem for windows xp only. unfortunately no one in tech support seems to know this.
I installed this printer on a couple of macs and the scan to computer was not an option so there was no disabling it. I will have to check to see if the printer goes off line for them.
but the issue of the xp computer not accessing the internet over night has been solved. but not a very good solution. you would think that hp engineers could figure out a better solution. Panasonic network copiers scan straight to any computer on the network with out any issues. best software I have ever run across.
04-11-2013 03:11 PM
You may need to take it one step further and add a port to your printer.
To do so, go into the control panel/hardware and sound/devices and printers. Find the Hp Officejet Pro icon and right click on it. Select printer properties and then click on the ports tab. Click on add port and select Standard TCP/IP Port. Next click on New Port and it will open a wizard to help configure it. In the first field enter the static IP port given to the printer. Once the wizard is finished, be sure the new IP Port is selected and click apply then ok.
This should "wake" your printer up. If after restarting your PC you find that the printer is offline again, go back to the ports tab and make sure the IP port is selected. If it continues to reset itself to the original port, you may want to delete the original port though I would do so only if it reset constantly.
08-26-2013 11:40 AM
My printer is connected to my computer via USB cable with the network function completely disabled and my printer still turns off. The only way I can reestablish connection is by turning it off and back on. It happens sometimes, but not others. If there's something I'm missing and could do to avoid this, I would really appreciate it.
It's otherwise a good printer with good quality and paperhandling.