cancel
Showing results for 
Search instead for 
Did you mean: 
Common problems for INSTANT INK, HP+ PLANS: INK AND TONER
We would like to share some of the most frequently asked questions about Instant Ink. Check out this link: HP INSTANT INK, HP+ PLANS: INK AND TONER. .
agatak
New member
1 0 0 0
Message 1 of 2
67
Flag Post

An issue with hp

HP Recommended
hp 2600 deskjet
Microsoft Windows 10 (32-bit)

agatak_1-1614529783979.png

 

1 REPLY 1
praveenbv
HP Support Agent
HP Support Agent
2,875 2,874 106 140
Message 2 of 2
Flag Post
HP Recommended

Hi@agatak,Welcome to the HP Support Community!

 

Check the ink cartridge numbers

 

Make sure the cartridge model numbers match your printer and country/region.

  1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

  2. Look for the model number on each of the cartridges.

  3. Go to the HP Store to verify they are compatible with the printer and your country/region.

  4. Replace any incompatible cartridges.

    NOTE: 

    HP+ printers require Original HP cartridges.

Reset the printer

Reset the printer to recover from printer errors or failures.

  1. If your printer has a rechargeable battery, remove it.

  2. With the printer turned on, disconnect the power cord from the printer.

  3. Unplug the power cord from the power source.

  4. Wait 60 seconds.

  5. Reconnect the power cord to a wall outlet and to the printer.

    NOTE: 

    HP recommends plugging the printer directly into a wall outlet.

  6. Turn on the printer to complete the reset.

Clean the ink cartridge and carriage electrical contacts

Remove any debris or buildup from the contacts on the cartridges and in the carriage.

  1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

  2. Remove the cartridge indicated in the error message from the carriage.

    • Carriages with cartridge latches: Open the latch, and then pull the cartridge up and out of the slot.

      Removing the ink cartridges with latches from the carriage

    • Carriages without cartridge latches: Gently press down on the cartridge to release it, and then pull it out of the slot.

      Removing the ink cartridges from the carriage

  3. Holding the cartridge by the sides, remove any protective tape that still might be on the contacts.

    CAUTION: 

    Do not touch the ink nozzles or the copper-colored electrical strip. Touching or trying to remove these parts can result in clogs, ink failure, and bad electrical connections.

    Removing tape from the ink cartridge

  4. Lightly dampen a lint-free cloth with distilled water, and then wipe the copper-colored contacts on the cartridge.

    Cleaning the ink cartridge contacts

  5. Lightly dampen a lint-free cloth or swab with distilled water, and then clean the electrical contacts in the carriage.

    Cleaning the contacts in the carriage

  6. Wait 10 minutes for the contacts to dry, and then reinsert the cartridge into its color-coded slot.

  7. Repeat these steps for the other cartridge if it was indicated in the error message.

  8. Close the door or lid to the cartridge access area.

    If the error persists, clean the cartridge and carriage contacts a second time.

Replace the problem ink cartridge

Installing a new cartridge can resolve ink-related errors.

  1. For best results, replace the cartridge with a genuine HP cartridge. To find your cartridge number and purchase HP ink supplies, go to the HP Store or a local retailer.

    NOTE: 

    If you have a defective HP cartridge, it might be under warranty. Go to About Original HP Cartridges for page yield and HP limited warranty information.

  2. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

  3. Remove the cartridge indicated in the error message, and then insert the new cartridge into the slot.

  4. Repeat these steps to replace any other cartridges indicated in the error message.

  5. Close the door or lid to the cartridge access area, and then follow any instructions to align the printer.

Keep me posted. Happy to help!

 

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Have a great day! 

Reply
0 Kudos
Warning Be alert for scammers posting fake support phone numbers and/or email addresses on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation