-
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.Windows 11 Support Center.
-
-
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.Windows 11 Support Center.
-
- HP Community
- Poly Phones
- Desk and IP Conference Phones
- Paging puts active call on hold.

Create an account on the HP Community to personalize your profile and ask a question

08-01-2019 02:10 AM
Phone Information Phone Model VVX 410 Part Number 3111-46162-001 Rev:A MAC Address 64:16:7F:94:F8:B7 IP Mode IPv4 IP Address 172.16.16.239 UC Software Version 5.6.1.1740 Updater Version 5.8.1.0055
i have problem when group pagging arrives phone puts active call on hold .
below is my config files with exported config file from phone as well.
Solved! Go to Solution.
Accepted Solutions
08-01-2019 01:37 PM
The below instruction assumes you are referring to the Multicast PTT feature supported by the VVX phone. If the paging feature you are using is third party (e.g. Broadsoft group paging over SIP), then the behavior will not follow the parameters the phone uses for Multicast PTT.
You will want to export the phone backup from the Web Configuration Utility of the phone (from Utilities > Phone Backup & Restore) and look for the following parameter:
ptt.pageMode.allowOffHookPages
Per the 5.6.0 Administrator's Guide, acceptable values for this parameter are:
- 0 (default) - Group pages do not play out on the phone during an active call except for Priority and Emergency pages.
- 1 - Group pages play out on the handset during an active call.
If the parameter is not found in the phone backup then it is currently set at the default value of "0". If that is the case, you may be receiving pages from Priority or Emergency groups, which will always have this behavior.
If the parameter is currently set to "1" then you may want to use the Web Configuration Utility to import the attached configuration file (from Utilities > Import & Export Configuration), which will set that parameter back to the default value of "0" -- you will need to extract the .zip file before attempting to import the contained .cfg file to the phone.
08-01-2019 01:37 PM
The below instruction assumes you are referring to the Multicast PTT feature supported by the VVX phone. If the paging feature you are using is third party (e.g. Broadsoft group paging over SIP), then the behavior will not follow the parameters the phone uses for Multicast PTT.
You will want to export the phone backup from the Web Configuration Utility of the phone (from Utilities > Phone Backup & Restore) and look for the following parameter:
ptt.pageMode.allowOffHookPages
Per the 5.6.0 Administrator's Guide, acceptable values for this parameter are:
- 0 (default) - Group pages do not play out on the phone during an active call except for Priority and Emergency pages.
- 1 - Group pages play out on the handset during an active call.
If the parameter is not found in the phone backup then it is currently set at the default value of "0". If that is the case, you may be receiving pages from Priority or Emergency groups, which will always have this behavior.
If the parameter is currently set to "1" then you may want to use the Web Configuration Utility to import the attached configuration file (from Utilities > Import & Export Configuration), which will set that parameter back to the default value of "0" -- you will need to extract the .zip file before attempting to import the contained .cfg file to the phone.

08-06-2019 06:08 AM
@polyben
i'm not using phone paging , i have configured it same like intercom
i have attached two config files one of which is my another working system's file it has alert-info="sipXpage" while where it is not working has alert-info=''RDZMQBJf"
tell me if i have missed something.
08-06-2019 08:48 PM
Hello @milansuthar ,
welcome back to the Poly community.
Some or a couple of your old post(s) or reply(s) to them => here <= are still open/pending as you have not marked these as "Accept as a solution" or at least provide some form of feedback or answer.
If they are in this state nobody finding them via a community search will know if an answer or advice provided was useful and has maybe helped you.
Could you therefore kindly go over them and mark or answer as appropriate?
If they are marked as "Accept as a solution" other users can find these easier and it helps them to utilize the community more efficiently. Please do not simply mark them without any type of feedback.
For your new issue, you are telling the Phone to Ring and then answer. This method will obviously do the same if you are in a call or not.
Oct 25, 2011 Question: How can I change my Ringtone or Ring in a special manner for a certain incoming call?
Resolution: Please check => here <=
The above FAQ describes this in detail. You can use a tool like Notepad++ to check for differences between the "working" configuration and the nonworking one.
Or use paging which all of our current phones have built-in via the PTT/Paging functionality.
Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.
Best Regards
Steffen Baier
Notice: This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge. If you need immediate and/or official assistance please open a service ticket through your support channels.
Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN
Didn't find what you were looking for? Ask the community