Ask questions. Help others.
The HP Community is here for you.
Post new question
Question
Reply
 
Note on archived topics.
This topic has been archived. Information and links in this thread may no longer be available or relevant.
If you have a question create a new topic by clicking here, or click on "Post new question" above and select the appropriate board.
Honor Student
Posts: 2
Member Since: ‎11-18-2013
Message 1 of 3 (347 Views)

m8020n - installing more ram to 4GB

I have an HP Pavillion Media Center PC m8020n.  I am wanting to upgrade the memory from the 2GB the computer shipped with (2 x 1GB modules installed in slots XIMM1 and XIMM3)  I reviewed the product specs for the m8020n and purchased Super Talent 2GB (2x1GB) DDR2-667 PTU08F16Q ram from ebay (link to listing attached). 

 

After installing the new mods into slots XIMM2 and XIMM4, the computer would not boot windows and would just hang after post.  I then switched respective pairs and fired up again with the same results.  I removed the original mods and the system would work at 2GB with the new mods installed, so I don't think the "new" mods are bad.

 

I tried several more combinations (I know there are around 136 combos with 4 mods and empty slots).  Sometimes it would post and not boot to windows, other times it would give one short beep  then one long beep and then repeat the beeping sequence after a long pause.  No matter what I tried, I could get the individual pairs to work together alone, but I could not get all 4 mods to "play nice" with each other.

 

Does anyone have any suggestions?  I am at bois 5.23 for this motherboard, which appears to be the latest available.

 

http://www.ebay.com/itm/380746046926?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

 

Thanks,

 

sometimeproblem

0 Kudos
Provost
Posts: 26,880
Member Since: ‎07-17-2009
Message 2 of 3 (334 Views)

Re: m8020n - installing more ram to 4GB

[ Edited ]

Hi,

 

HP typically recommends that all four dimms be matched in speed and CAS specifications to avoid problems.  There are other specifications that can also cause problems hence the recommendation that all dimms be the same.  The HP bios can be very finikey with dimm compatibility.

 

Use can use CPU-Z to verify the specifications of each dimm to ensure that they are in fact the same specifications.

 

If the dimms are in fact the same specification then try clearing the CMOS.

 

 

HP laptop 17t u100,
HP Photosmart 6520 and HP Deskjet 1112
Custom 1151 socket Z270 Intel i7-7700k @4,600 Mhz, 16GB Corsair 3000 Mhz dimms
Corsair H75 water cooler, Corsair CS 650M power supply
RAID 0 (dual Samsung 960 EVO m.2 240GB) boot system
Dual Samsung 840 EVO SSDs 500GB data storage, Intel 750 PCIe SSD 400GB
MSI NVIDIA GTX 980TI 6GB
ASUS ROG PG279q @144 MHz
Windows 10 and Windows 8.1 Pro x64 in UEFI mode
Highlighted
Honor Student
Posts: 2
Member Since: ‎11-18-2013
Message 3 of 3 (319 Views)

Re: m8020n - installing more ram to 4GB

Thanks for the replay.

 

I understand the recomendation your suggesting.  I have not tried clearing the CMOS before.  What does that do?

 

The only recommendation I had seen for this board was to always install in matched pairs and to limit the bus speed to 667, and that the timings and latency would be matched and limited by BIOS.  I even ran the scan tool at Crucial.com and it suggested I buy PC2-5300 to go into my machine that had (2) 1GB modules of PC2-4200U installed from factory.

 

If the CMOS doesn't work, then sounds like either way I am stuck with a pair of modules I can't use.  Since both pair of modules work when installed independently, I will probably buy another pair that will match the higher bus speed mods.

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation