• ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
Are you having HotKey issues? Click here for tips and tricks.
Locked

‎10-07-2020 07:18 AM

HP Recommended
Product: Z820, Z840, Z8
Operating System: Microsoft Windows 10 (64-bit)

I would like to configure our HP Z8xx Workstations to start up after power is resumed after a power failure.

We are working remotely due to Covid and I am wondering if there is a way to enable this feature via Windows 10, without having to boot each system into the BIOS. We have remote access, but not to the 'system' level like iLO. I would like configure this without having to go into the office.

1 ACCEPTED SOLUTION

Accepted Solutions

‎10-07-2020 01:21 PM - edited ‎10-07-2020 01:27 PM

HP Recommended

You can modify the BIOS settings from within Windows if you have HP Performance Advisor installed on the machines. HP Performance Adivisor is a free workstation maintenance and diagnostic tool from HP.

 

In the BIOS section;

Advanced > After Power Loss - can be set to Off, On, or Previous State

Unfortunately, to apply any BIOS changes, you still need to reboot the computer.

HP Z620 - Liquid Cooled E5-1680v2 @4.7GHz / 64GB Hynix PC3-14900R 1866MHz / GTX1080Ti FE 11GB / Quadro P2000 5GB / Samsung 256GB PCIe M.2 256GB AHCI / Passmark 9.0 Rating = 7147 / CPU 17461 / 2D 1019 / 3D 14464 / Mem 3153 / Disk 15451 / Single Threaded 2551

View solution in original post

Was this reply helpful? Yes No
1 REPLY 1

‎10-07-2020 01:21 PM - edited ‎10-07-2020 01:27 PM

HP Recommended

You can modify the BIOS settings from within Windows if you have HP Performance Advisor installed on the machines. HP Performance Adivisor is a free workstation maintenance and diagnostic tool from HP.

 

In the BIOS section;

Advanced > After Power Loss - can be set to Off, On, or Previous State

Unfortunately, to apply any BIOS changes, you still need to reboot the computer.

HP Z620 - Liquid Cooled E5-1680v2 @4.7GHz / 64GB Hynix PC3-14900R 1866MHz / GTX1080Ti FE 11GB / Quadro P2000 5GB / Samsung 256GB PCIe M.2 256GB AHCI / Passmark 9.0 Rating = 7147 / CPU 17461 / 2D 1019 / 3D 14464 / Mem 3153 / Disk 15451 / Single Threaded 2551
Was this reply helpful? Yes No
Warning
Be alert for scammers posting fake support phone numbers and/or email addresses on the community.
If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.
Didn't find what you were looking for? Ask the community
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.