• ×
    Information
    Windows update impacting certain printer icons and names. Microsoft is working on a solution.
    Click here to learn more
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Windows update impacting certain printer icons and names. Microsoft is working on a solution.
    Click here to learn more
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
Do you need the WPS PIN to connect your printer? Click here for tips and tricks!
Get help with Large Format Printers, with direct access to all Large Format Knowledge Center· Ask anything · Find anything · Share anything at HP LKC
Locked

‎09-18-2019 01:26 PM

HP Recommended
Product: DesignJet T790
Operating System: Microsoft Windows 7 (32-bit)

I haven't used my printer in a few years. Had to replace all the ink cartridges. Then it said I had a bad printhead (MK-Y, C9384A). Bought a new one. Pulled out the old one and installed the new one, just as the instructions specified. Then it told me I had "not completed the installation". No other explanation of HOW I "had not completed the installation" or what further actions I needed to take. Printer still will not work. Cannot get through to a live person at HP to help. Can anyone help me?

3 REPLIES 3

‎09-19-2019 05:18 AM

HP Recommended

Is this the 24" or 44" size printer?

 

I had a 24" T790 with the exact same issue.  Unused for sometime when I got it.  I think I tracked it down to a bad service station.  Couldn't get it to take a printhead or ink cartridge.  Then it started throwing crazy errors about the ink cartridges being out of date and showing dates of 1968.  Firmware updates didn't help.  

 

Good luck.  Let us know updates.

 

 

I don't work for HP....I just repair their printers.
Was this reply helpful? Yes No

‎09-19-2019 05:25 AM

HP Recommended

found something but don't know if it helps...

https://www.lpscomputer.com/blogs/news/printhead-replacement-incomplete-on-designjet-t-and-z-printer...

Was this reply helpful? Yes No

‎09-19-2019 05:31 AM - edited ‎09-19-2019 05:39 AM

HP Recommended

Sorry, forgot to include link to service manual:

 

http://www.partshere.com/models/hpmanuals.asp?model=CR649A

 

It will show you how to use a torx driver to release the carriage so you can access the printheads.  Or you can let the carriage move towards center and use the power switch to turn it off.  Either way, you'll need to access the carriage and remove all the printheads and use the syringe priming tool to try to draw ink through the lines.  Tool can be purchased here:  https://www.lpscomputer.com/collections/designjet-t1300-t2300-parts-page

 

Inserting the syringe too far can accidently damage the  valve.

I don't work for HP....I just repair their printers.
Was this reply helpful? Yes No
Warning
Be alert for scammers posting fake support phone numbers and/or email addresses on the community.
If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.

Didn't find what you were looking for? Ask the community

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.