cancel
Showing results for 
Search instead for 
Did you mean: 
  • ×
    Information
    Need Windows 11 help?
    Check documents and videos on compatibility, FAQs, upgrade information and available fixes.Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents and videos on compatibility, FAQs, upgrade information and available fixes.Windows 11 Support Center.
  • post a message
Get help with Large Format Printers, with direct access to all Latex Knowledge Center · Ask anything · Find anything · Share anything at HP LKC
CADSURVR
New member
3 2 0 0
Message 1 of 5
313
Flag Post

Solved!

Plotter Issue

HP Recommended
designjet T210
Microsoft Windows 10 (64-bit)

My brand new designjet T210 plotter only prints the right hand side of the page no matter what the settings are set to.  It has 24" wide roll media.  The preview always looks fine but the output always the same, half a sheet. I've unloaded & reloaded the drivers but to no avail.

Please help, it's about to go out the window!

1 ACCEPTED SOLUTION

Accepted Solutions
HarryCR
Level 5
Level 5
200 199 14 22
Message 2 of 5
Flag Post
HP Recommended

Hello @CADSURVR 

 

Try going to the properties and then to the preferences

HarryCR_0-1612190205084.png

 

then select Max. Application Resolution and set it as 300

 

HarryCR_1-1612190249072.png

 

then try printing. Usually this takes care of issue when only print half of the jobs.

 

Regards. 

 

I am an HP employee

View solution in original post

Was this reply helpful? Yes No
4 REPLIES 4
HarryCR
Level 5
Level 5
200 199 14 22
Message 2 of 5
Flag Post
HP Recommended

Hello @CADSURVR 

 

Try going to the properties and then to the preferences

HarryCR_0-1612190205084.png

 

then select Max. Application Resolution and set it as 300

 

HarryCR_1-1612190249072.png

 

then try printing. Usually this takes care of issue when only print half of the jobs.

 

Regards. 

 

I am an HP employee
Was this reply helpful? Yes No
CADSURVR
Author
New member
3 2 0 0
Message 3 of 5
Flag Post
HP Recommended

Thanks so much, that seems to do the trick. Can't help but wonder though, why you would even have a resolution of 600 &/or auto select if it does not work! Is it a plotter memory thing or a spooler memory thing? If I wanted to plot at the higher resolution would you have to allocate additional memory to the plotter or the spooler?

Happy with it just working. . .. Just curious.

Thnx again Harry

Was this reply helpful? Yes No
HarryCR
Level 5
Level 5
200 199 14 22
Message 4 of 5
Flag Post
HP Recommended

@CADSURVR  good to know that it is working fine for you.

 

I thought the same, why there is a 600dpi and the auto as well, I guess that because the printer is design for Technical drawings they don't need 600 dpi of resolution and the auto is not properly working, we will see a future driver version and I hope this will ask our questions.

 

Regards.

I am an HP employee
Was this reply helpful? Yes No
CADSURVR
Author
New member
3 2 0 0
Message 5 of 5
Flag Post
HP Recommended

Will do for now!

Back to work. 🙂

Was this reply helpful? Yes No
Warning Be alert for scammers posting fake support phone numbers and/or email addresses on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation