• ×
    Information
    Windows update impacting certain printer icons and names. Microsoft is working on a solution.
    Click here to learn more
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Windows update impacting certain printer icons and names. Microsoft is working on a solution.
    Click here to learn more
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
We have new content about Hotkey issue, Click here to check it out!
HP Recommended
Hp elite 7500
Microsoft Windows 10 (64-bit)

Hello I accidently changed some options in the uefi pci vga config and after I s a very those settings my hp elite 7500 series restarted and th screen dint work anymore so then I tried to reset the cmos and after that when I turned it on it started beeping 6 times with a yellowish colour and the screen still sin

1 ACCEPTED SOLUTION

Accepted Solutions
HP Recommended

If your PC had a setting to use the Nvidia graphics card, then you probably need to remove the Nvidia graphics card.

 

Your PC's motherboard has an onboard Intel graphics adapter and a Nvidia graphics adapter would have to be a removable card.

 

Below is the link to the service guide where you can find the procedure to remove and replace a video card.

 

See chapter 7, pages 61 - 67.

 

c03550633.pdf (hp.com)

View solution in original post

7 REPLIES 7
HP Recommended

Hi:

 

If you have an add-on graphics card installed, the only suggestion I can offer would be to remove the card and then set the BIOS to its defaults.

 

See this link for more information...

 

HP Desktop PCs - Computer Does not Start After Installing a Video Card (Windows 10, 😎 | HP® Custome...

HP Recommended

From my knowledge  the the pc is not using a another graphic card I am not well versed in this but when I was in the pci vga config the options were to set one of them as primary one of them was intel and the other one was nividia .  in the device manager it wasn't showing which graphic card I was using so I went ot the uefi and changed the primary to intel and restarted and bam 6 beeps

HP Recommended

If your PC had a setting to use the Nvidia graphics card, then you probably need to remove the Nvidia graphics card.

 

Your PC's motherboard has an onboard Intel graphics adapter and a Nvidia graphics adapter would have to be a removable card.

 

Below is the link to the service guide where you can find the procedure to remove and replace a video card.

 

See chapter 7, pages 61 - 67.

 

c03550633.pdf (hp.com)

HP Recommended

I have removed the video card and it works I think .. it runs without any beeps but I don't have dvi cable so I can't check my moniter but I'm certain it worked thx alot ill get dvi cable tommorow and report back if it worked.. either way thanks

HP Recommended

You're very welcome.

 

If you have set the BIOS to its defaults, you can try reinstalling the video card and see if it works from the Nvidia card again.

 

It might.

 

If it doesn't then for some reason the Nvidia graphics card may have suffered a hardware failure and you can remove it again and continue to run the PC from the onboard Intel graphics.

HP Recommended

K i will do that , thanks alot again

HP Recommended

You're very welcome.

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.