cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Level 1
7 4 0 0
Message 1 of 7
1,161
Flag Post
HP Recommended

Can I skip pressing F1 when the motherboard detects erros

HP DC 6005
Microsoft Windows 7 (32-bit)

there is a HP compaq PC,I have to press F1 to let it continue to boot everytime because the motherboard can detect the errors below:

921-Front USB 1 not connected

please now how to disable this message

because my front usb port is not working properly so i can only by pass this F1 message or another way if front usb disable from bios then also would be ok

6 REPLIES 6
Highlighted
Level 15
Level 15
9,983 9,979 937 2,733
Message 2 of 7
1,139
Flag Post
HP Recommended

Can I skip pressing F1 when the motherboard detects erros

Assuming the reason for the message is the front USB ports are malfunctioning, you could disconnect them and that will stop the message.

This manual has a picture showing where the front USB ports connect to the motherboard - lower right of picture  green connection block and yellow connection block.  Typically there is a plug that fits the pin block, but it could be individual connections.  Make a note or take a picture to identify how they are connected for future reference.






I'm not an HP employee.
Did this message answer your question? Please indicate below as an Accepted Solution!
Did you find this message useful? Click on the thumbs up to give Kudos! " >.

0 Kudos
Highlighted
Level 1
7 4 0 0
Message 3 of 7
1,069
Flag Post
HP Recommended

Can I skip pressing F1 when the motherboard detects erros

my usb port not working cause of damage IC so that's way disconnect the front usb port and u know hp dc6005 given you tow other front panel usb port

i am using these port for front panel using but problem is this any starting time show this message

 

sorry for my poor english

0 Kudos
Highlighted
Level 15
Level 15
9,983 9,979 937 2,733
Message 4 of 7
1,055
Flag Post
HP Recommended

Can I skip pressing F1 when the motherboard detects erros

In looking at my previous post, I forgot to include the link to the manual, so here is the manual

http://h10032.www1.hp.com/ctg/Manual/c01883663

Here is the picture I referenced

2019-04-04 06_29_30-Window.jpg

There is a spare set of USB headers, (toward the right in that picture) which you could try but if that does the same thing as the other header, it could be a wiring problem on the front USB ports.  In that case, just leave the header disconnected and use the rear USB ports.






I'm not an HP employee.
Did this message answer your question? Please indicate below as an Accepted Solution!
Did you find this message useful? Click on the thumbs up to give Kudos! " >.

0 Kudos
Highlighted
Level 1
7 4 0 0
Message 5 of 7
953
Flag Post
HP Recommended

Can I skip pressing F1 when the motherboard detects erros

here is extra front usb pin out

so i am using this one and my problem is solved

 

thanks for your suggestion

0 Kudos
Highlighted
Level 15
Level 15
9,983 9,979 937 2,733
Message 6 of 7
943
Flag Post
HP Recommended

Can I skip pressing F1 when the motherboard detects erros

Excellent.  Glad that extra header was available.






I'm not an HP employee.
Did this message answer your question? Please indicate below as an Accepted Solution!
Did you find this message useful? Click on the thumbs up to give Kudos! " >.

Highlighted
Level 1
7 4 0 0
Message 7 of 7
913
Flag Post
HP Recommended

Can I skip pressing F1 when the motherboard detects erros

thanks for your suggestions and helping

 

please now close this thread

0 Kudos
Be alert for scammers posting fake support phone numbers on the community. If you think you have received a fake HP Support message, please report it to us by clicking on "Flag Post".
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation