• ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
Are you having HotKey issues? Click here for tips and tricks.
HP Recommended
Microserver Proliant N54l
Linux

Sorry to post under Desktop Boot and Lockup, but I couldn't find a bether option...

 

I'm trying to install a second ethernet interface on my Microserver Proliant N54l, but I'm facing some difficulties. Running LINUX )i've tryied with UBUNTU 20.04 and DEBIAN 10) I noticed that both enp2s0 and enp3s0 are renamed after eth0, which shouldn't happen. 

 

After configuring /etc/network/interfaces with my configuration and restarting the service, enp3s0 goes down. I have to manually bring it up again (ifup enp3s0).

 

After initial boot, dmesg returns:

 

root@servidor:~# dmesg | grep enp
[ 2.290238] r8169 0000:02:00.0 enp2s0: renamed from eth0
[ 2.305776] tg3 0000:03:00.0 enp3s0: renamed from eth0
[ 4.584484] r8169 0000:02:00.0 enp2s0: unable to load firmware patch rtl_nic/rtl8168e-3.fw (-2)
[ 4.693493] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
[ 5.510217] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 8.529895] tg3 0000:03:00.0 enp3s0: Link is up at 1000 Mbps, full duplex
[ 8.529924] tg3 0000:03:00.0 enp3s0: Flow control is on for TX and on for RX
[ 8.529968] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[ 17.378978] r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 17.378997] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready

 

I loaded optimal settings on BIOS, but nothing has changed

 

As you can see, both interfaces enp have been named after eth0. I believe it should be one after eth0 and the other after eth1.

 

I replaced the card, but nothing has changed.

 

Is there any jumper configuration on motherboard? Or any other detail?

 

Thanks

 

 

3 REPLIES 3
HP Recommended

Hi:

 

HP split into two companies several years ago.

 

HP supports PC's, printers, tablets and calculators.

 

HP Enterprise (HPE) supports servers, switches, routers and tape drives.

 

You may want to post your question on the HPE community support forum -- Proliant Netservers section...

 

ProLiant Servers – Netservers Forum | HPE Blogs, Discussions and Forums Community

HP Recommended

Thank you very much!!!! I will!!

HP Recommended

You're very welcome.

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.