Guidelines
Are you having HotKey issues? Click here for tips and tricks.
Check out our WINDOWS 11 Support Center info about: OPTIMIZATION, KNOWN ISSUES, FAQs, VIDEOS AND MORE.
HP Recommended
hp slimline 290 p0043w
Microsoft Windows 11

when i press power on tower it does 3 longs beeps and 2 short beeps and no display on the monitor.

1 ACCEPTED SOLUTION

Accepted Solutions
HP Recommended

hi

HP Slimline 290-p0043w Desktop PC Product Specifications


you probably have a problem with the memory module
in its original configuration it is mentioned 4 gb
I can't know if it's one or two modules
so if only one, it will probably have to be replaced and
if you have two, you have to test one and then the other

Take the recommended precautions, to open a computer
after unplugging the plug, keep pushing the power button for a while
if only one module
remove the module, then replace it correctly, possibly in another slot
reconnect everything, and restart!
no better, you have to buy an identical module, or why not install more

  • Amount: 4 GB
  • Speed: PC4-19200 MB/s
  • Type: DDR4-2400

 

  • Dual channel memory architecture
  • Two DDR4 UDIMM (288-pin) sockets
  • Supports up to PC4-21300 (DDR4 2666)
  • Supports 4 GB and 8 GB DDR4 UDIMMs
  • Supports up to 4 GB on 32-bit systems
    note:
    32-bit systems cannot address a full 4.0 GB of memory.
  • Supports up to 8 GB (unbuffered) on 64-bit computers

try scan and manual search :

Welcome to Crucial USA

 

--------------------------------------------- Signature ---------------------------------------------
was this reply helpful , or just say thank you ? Click on the yes button

Please remember to mark the answers this can help other users
please click on the accept as solution button if message provided an answer to the problem




Desktop-Knowledge-Base
Windows 11 22h2 inside , user

------------------------------------------------------------------------------------------------------------

View solution in original post

1 REPLY 1
HP Recommended

hi

HP Slimline 290-p0043w Desktop PC Product Specifications


you probably have a problem with the memory module
in its original configuration it is mentioned 4 gb
I can't know if it's one or two modules
so if only one, it will probably have to be replaced and
if you have two, you have to test one and then the other

Take the recommended precautions, to open a computer
after unplugging the plug, keep pushing the power button for a while
if only one module
remove the module, then replace it correctly, possibly in another slot
reconnect everything, and restart!
no better, you have to buy an identical module, or why not install more

  • Amount: 4 GB
  • Speed: PC4-19200 MB/s
  • Type: DDR4-2400

 

  • Dual channel memory architecture
  • Two DDR4 UDIMM (288-pin) sockets
  • Supports up to PC4-21300 (DDR4 2666)
  • Supports 4 GB and 8 GB DDR4 UDIMMs
  • Supports up to 4 GB on 32-bit systems
    note:
    32-bit systems cannot address a full 4.0 GB of memory.
  • Supports up to 8 GB (unbuffered) on 64-bit computers

try scan and manual search :

Welcome to Crucial USA

 

--------------------------------------------- Signature ---------------------------------------------
was this reply helpful , or just say thank you ? Click on the yes button

Please remember to mark the answers this can help other users
please click on the accept as solution button if message provided an answer to the problem




Desktop-Knowledge-Base
Windows 11 22h2 inside , user

------------------------------------------------------------------------------------------------------------
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.