HP Omen laptop will turn on but stuck on a black screen.

[GD99]

It turns on and shows the Omen logo then loads, after it load it goes to a black screen and if I move my mouse around it shows the mouse on the screen then goes away when i stop moving it. 

[Lil_Boy_Blue]

Hi
First:- Turn off the computer, press and hold the PWR button for 4 seconds.

Then - Leave only keyboard and mouse connected, disconnect all externally connected
devices such as Docking Station, USB storage devices, displays, and printers.
Unplug the AC adapter from the computer.

Next - Press and Hold the Power button for 15 seconds to Hard Reset.
Rinse and Repeat

NOW begin checking/testing/proving the Hardware is fit for purpose.
Power on your PC, press ESC (repeatedly), then F2 at the prompt.
Choose System Tests (Fast Test does a 4 minute hardware check).
AND/OR
HOW DO I USE DIAGNOSTICS?

HP PC Hardware Diagnostics Windows is a Windows-based utility that allows you to run diagnostic tests to determine if the computer hardware is functioning properly. The tool runs within the Windows operating system in order to diagnose hardware failures. HP PC Hardware Diagnostics Windows comes pre-installed on new HP computers, but if not on yours, download here:- http://ftp.hp.com/pub/softpaq/sp93001-93500/sp93457.exe

This will not work for everyone, but you may be lucky?

HP Notebooks and Mobile Workstations -
No Power, No Boot, No Display When Power Button Is Pressed

NOTE: Be sure the battery is installed in the computer and it has sufficient power before continuing. Due to the design of the Embedded Controller/Keyboard Controller, the power supply must be disconnected and the computer must be powered with battery power to reset the Embedded Controller/Keyboard Controller.

Unplug the AC power from the computer.
Press and hold the power button for more than 12 seconds.
Release the power button (after at least 12 seconds).
The computer will power on and should boot normally after releasing the power button.
Re-connect the AC power to the computer.

NOTE: In case the battery is not charging after performing the steps to reset the Embedded Controller, unplug and re-plug in the AC power again.

[GD99]

so i did the fast test thing and it said everything had passed and it went to start up but when it was loading it once again just use a black screen. after turning it off and on again it brought up another screen saying how it couldn’t shut down properly - i went to do the recovery option and tried resetting my laptop so it removes all the apps but it can’t even do that either it just says error

[Lil_Boy_Blue]

From 2016 onwards there is a possible recovery option via the cloud...
HP Consumer PCs - Using the HP Cloud Recovery Tool (Windows 7 & 10)
https://support.hp.com/us-en/document/c06162205
OR
This First part only works when a valid Recovery Partition is enabled.

If it displays an error message then move onto the Second part,
OR if you have data you wish to try and save using the XCOPY command.
Then create your own Repair/Recovery/Rebuild/Re-install media or buy a set from HP.

Turn off the computer.

Disconnect all connected devices and cables, Media Drives, USB drives, printers, & faxes.
Remove media from internal drives, and remove any recently added internal hardware.
Do not disconnect the monitor, keyboard, mouse, or power cord.

Turn on the computer and repeatedly press the F11 key, about once every second,
until the Choose an option screen is displayed, and then continue.

On the Choose an Option screen, click Troubleshoot, and work your way through the screens.

Second Part:-
This may require another PC. Find and Download your .iso from…
(You will need a NON_OEM key for W7;
W8.x and W10 should activate automagically from their embedded licence key.)

https://www.microsoft.com/en-us/software-download/windows7
https://www.microsoft.com/en-us/software-download/windows8ISO
https://www.microsoft.com/en-us/software-download/windows10

For when it’s a NON MS OS ( iOS / Linux ) creating the install media.
www.microsoft.com/en-us/software-download/windows10ISO

A 3rd party site like…
https://www.heidoc.net/joomla/technology-science/microsoft/67-microsoft-windows-iso-download-tool

Expand/Extract/Burn the iso Image onto a DVD/USB as needed.
Microsoft’s Creator Tool will make the required DVD or USB.

Even though it has NO actual HP software/drivers included, you may be able to
XCOPY the C:\Users\* area onto a ‘large’ USB stick, via the Command Prompt.

You’ll need to try various drive letters; D:..-..Z: until it’s matched - could be G; mine’s S:

C:\>XCOPY C:\Users\* S:\ /e /i /h (then files like those 3 listed below get copied over)

C:\Users\desktop.ini
C:\Users\All Users\agent.1509128044.bdinstall.bin
C:\Users\All Users\HP Deskjet 2540 series\Help\flash\zoom.swf

Then you can try System Recovery Options / Advanced Options shown in the screenshots.

NB:- W7 Try running a Startup Repair more than once for a full fix.
NB: - W10 Begin with the Automatic Repair, then Startup Settings etc.

From either the C:\ or the X:\ prompt try the following

cd boot
bootrec /FixMBR
bootrec /FixBoot
bootrec /RebuildBCD

If the above FAILS then please try:-
http://www.thewindowsclub.com/repair-master-boot-record-mbr-windows
http://www.thewindowsclub.com/install-windows-7-from-usb
http://www.thewindowsclub.com/install-windows-10-from-usb