Guidelines
The HP Community is where owners of HP products, like you, volunteer to help each other find solutions.
Archived This topic has been archived. Information and links in this thread may no longer be available or relevant. If you have a question create a new topic by clicking here and select the appropriate board.
HP Recommended
J9651A
Microsoft Windows 10 (64-bit)

I have got an HP e-MSM430 acces point from a friend and i want to try to get this working at home.

Access point is resetted.

 

When i follow the manual step bij step, but i'm stuck in the inlog

 

A. Configure your computer
1. Disconnect your computer LAN port and configure it to use a static IP
address in the range 192.168.1.2 to 192.168.1.254, and a subnet mask
of 255.255.255.0. Set the default gateway to 192.168.1.1, and DNS
server to 192.168.1.1.
2. Disable any wireless connection on your computer.
B. Connect the cables and power on the AP
1. Connect the cables:
• If using a PoE switch, use Ethernet cables to connect your
computer and the AP to an unused factory-default PoE switch.
• If using a PoE injector, use Ethernet cables to connect your
computer to the data in port of the PoE injector and the AP to the
data and power out port of the PoE injector.
2. Power on the AP by powering on the PoE switch or injector.
Initially, the AP power LED blinks once every two seconds. Wait
approximately a minute until it begins blinking once per second before
proceeding to the next step.
C. Switch the AP to autonomous mode
Note: A factory-default AP is assumed.
1. In a web browser, enter the address: https://192.168.1.1.
2. A security certificate warning is displayed the first time you connect to the
management tool. This is expected behavior. Select whatever option is
needed in your web browser to continue to the management tool.

 

On the Login page, specify admin for both Username and Password
and then select Login.

 

I'm in the login page.

What I try, the username and password are not admin / admin

 

Please help.

3 REPLIES 3
HP Recommended

Hi,

 

Back to Factory setting, both usewrname and password use admin.

 

      http://h10032.www1.hp.com/ctg/Manual/c03738358

 

Why you have to do that lenghthy process, there is a small button (called Reset button), use a pin or paper clip to pess it few seconds and it will be reset back to factory default.

 

Regards.

BH
***
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.




HP Recommended

I just have take a look at youtube and saw a video.

While put reset button you have to hold the button for some few seconds. After blinking all the leds for 3 times it worked.

 

Now a new chapter will arrive for a dummy in networking 😉

 

I have wifi network at home.

How can i arrange that access point is connected with this wifi router?

 

Easy way?

HP Recommended

@pilske wrote:

..... I have wifi network at home.

How can i arrange that access point is connected with this wifi router?

 

Easy way?


Hi,

 

Please check the above document, on ly few steps. But why you need it in the first place ? Is there any problem with the existing network ?

 

Regards.

BH
***
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.




Archived This topic has been archived. Information and links in this thread may no longer be available or relevant. If you have a question create a new topic by clicking here and select the appropriate board.
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.