cancel
Showing results for 
Search instead for 
Did you mean: 
Jasmine1996
New member
1 0 0 0
Message 1 of 3
5,596
Flag Post

Solved!

HP Sprocket Flashing light

HP Recommended
Hp Sprocket Photo Printer X7N07A
iOS

my photo printer chraging light is flashinging red and green at the same time. When i try to charge it using the cord that it came and a wall charger. I was wondering what I need to do in order to fix this problem. Because my hp sprocket has been chargin for about 8 hours and won't turn on because the charging light keeps flashing red and green at the same time.

0 Kudos
1 ACCEPTED SOLUTION

Accepted Solutions
mGallo
Level 2
9 9 2 0
Message 2 of 3
Flag Post
HP Recommended

Hi! @Jasmine1996, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!

 

I understand your sprocket wont turn on and the LED light is flashing red and green.

 

Don't worry I'll try to help you out.

 

Did you make any changes to your printer?

 

Try the steps recommended below.

 

Please try few steps recommended below.

 

1.    Reset the Sprocket unit by placing a push-pin or needle into the small hole on the rear of the unit.  (Reset instructions in the support doc HERE)
2.    Plug in the Sprocket unit with the provided micro-USB cable.  Connect to either a computer USB port or USB wall charger.
3.    Allow the Sprocket unit to charge for 10 minutes.  Note:  A call back may be required in these instances.
4.    Power on the Sprocket unit by pressing/holding the power button for 3 seconds.
5.    A white LED should illuminate on the rear of the unit if power up is successful.
6.    Remind the customer to charge their Sprocket for an additional 60-90 minutes to enable a full battery charge.
 

 

If the issue still persists uninstall the sprocket app and reinstall the app and try updating the sprocket firmware from the sprocket app and check if it helps.

 

Open Sprocket app go to menu-->Sprocket---> Printers; A blue firmware update link will be present if an update is available.

 

Refer this article to know more information about using sprocket printer.

 

Also, refer the printer user guide for more information.

 

If the issue persists after trying out the steps, please contact HP support for service options.

 

Link to contact HP.

 

 

Let me know if this helps!

Have a pleasant day ahead! Smiley Happy

 

 

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

                                                                                                                  

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

 

View solution in original post

0 Kudos
2 REPLIES 2
mGallo
Level 2
9 9 2 0
Message 2 of 3
Flag Post
HP Recommended

Hi! @Jasmine1996, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!

 

I understand your sprocket wont turn on and the LED light is flashing red and green.

 

Don't worry I'll try to help you out.

 

Did you make any changes to your printer?

 

Try the steps recommended below.

 

Please try few steps recommended below.

 

1.    Reset the Sprocket unit by placing a push-pin or needle into the small hole on the rear of the unit.  (Reset instructions in the support doc HERE)
2.    Plug in the Sprocket unit with the provided micro-USB cable.  Connect to either a computer USB port or USB wall charger.
3.    Allow the Sprocket unit to charge for 10 minutes.  Note:  A call back may be required in these instances.
4.    Power on the Sprocket unit by pressing/holding the power button for 3 seconds.
5.    A white LED should illuminate on the rear of the unit if power up is successful.
6.    Remind the customer to charge their Sprocket for an additional 60-90 minutes to enable a full battery charge.
 

 

If the issue still persists uninstall the sprocket app and reinstall the app and try updating the sprocket firmware from the sprocket app and check if it helps.

 

Open Sprocket app go to menu-->Sprocket---> Printers; A blue firmware update link will be present if an update is available.

 

Refer this article to know more information about using sprocket printer.

 

Also, refer the printer user guide for more information.

 

If the issue persists after trying out the steps, please contact HP support for service options.

 

Link to contact HP.

 

 

Let me know if this helps!

Have a pleasant day ahead! Smiley Happy

 

 

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

                                                                                                                  

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

 

View solution in original post

0 Kudos
Ginger321
New member
1 1 0 0
Message 3 of 3
Flag Post
HP Recommended

@mGallo wrote:

Hi! @Jasmine1996, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!

 

I understand your sprocket wont turn on and the LED light is flashing red and green.

 

Don't worry I'll try to help you out.

 

Did you make any changes to your printer?

 

Try the steps recommended below.

 

Please try few steps recommended below.

 

1.    Reset the Sprocket unit by placing a push-pin or needle into the small hole on the rear of the unit.  (Reset instructions in the support doc HERE)
2.    Plug in the Sprocket unit with the provided micro-USB cable.  Connect to either a computer USB port or USB wall charger.
3.    Allow the Sprocket unit to charge for 10 minutes.  Note:  A call back may be required in these instances.
4.    Power on the Sprocket unit by pressing/holding the power button for 3 seconds.
5.    A white LED should illuminate on the rear of the unit if power up is successful.
6.    Remind the customer to charge their Sprocket for an additional 60-90 minutes to enable a full battery charge.
 

 

If the issue still persists uninstall the sprocket app and reinstall the app and try updating the sprocket firmware from the sprocket app and check if it helps.

 

Open Sprocket app go to menu-->Sprocket---> Printers; A blue firmware update link will be present if an update is available.

 

Refer this article to know more information about using sprocket printer.

 

Also, refer the printer user guide for more information.

 

If the issue persists after trying out the steps, please contact HP support for service options.

 

Link to contact HP.

 

 

Let me know if this helps!

Have a pleasant day ahead! Smiley Happy

 

 

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

                                                                                                                  

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

 


@mGallo wrote:

Hi! @Jasmine1996, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!

 

I understand your sprocket wont turn on and the LED light is flashing red and green.

 

Don't worry I'll try to help you out.

 

Did you make any changes to your printer?

 

Try the steps recommended below.

 

Please try few steps recommended below.

 

1.    Reset the Sprocket unit by placing a push-pin or needle into the small hole on the rear of the unit.  (Reset instructions in the support doc HERE)
2.    Plug in the Sprocket unit with the provided micro-USB cable.  Connect to either a computer USB port or USB wall charger.
3.    Allow the Sprocket unit to charge for 10 minutes.  Note:  A call back may be required in these instances.
4.    Power on the Sprocket unit by pressing/holding the power button for 3 seconds.
5.    A white LED should illuminate on the rear of the unit if power up is successful.
6.    Remind the customer to charge their Sprocket for an additional 60-90 minutes to enable a full battery charge.
 

 

If the issue still persists uninstall the sprocket app and reinstall the app and try updating the sprocket firmware from the sprocket app and check if it helps.

 

Open Sprocket app go to menu-->Sprocket---> Printers; A blue firmware update link will be present if an update is available.

 

Refer this article to know more information about using sprocket printer.

 

Also, refer the printer user guide for more information.

 

If the issue persists after trying out the steps, please contact HP support for service options.

 

Link to contact HP.

 

 

Let me know if this helps!

Have a pleasant day ahead! Smiley Happy

 

 

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

                                                                                                                  

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

 




 

0 Kudos
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation