• ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
The Poly Phones Knowledge Base is live! We look forward to helping you with common issues and troubleshooting advice!
HP Recommended

Hi,

 

we are developing a provisioning server and are now in the progress to move our provisioning server address to a new one.

 

Usually we reset the phones (VVX 411/211) and RealPresence Trio 8800, but we don't like to do this with devices we have already rolled out.

 

Is it possible to trigger a ZTP reconfiguration for devices whose ZTP data have been changed without rebooting or resetting the device?

 

There is a polling option on ZTP we have tried to use but without effect, because the device did not contact ZTP.

(I assume the polling option only gets activated once the device get rebooted)

 

Any help?

 

Thanks,

 

Lothar Behrens

3 REPLIES 3
HP Recommended

Hello Lothar Behrens,


welcome to the Polycom Community.

You will have to reboot the devices.

Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.

Best Regards

Steffen Baier

Polycom Global Services

------------------------------------------------
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.

Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN
HP Recommended

Thank you,

 

I have tested the relocation of our provisioning service by restarting the system and restarting the telephone and also rebooting the system and the telephone. Nothing has changed.

 

I was only able to relocate by factory reset.

 

This has been tested with two Trio 8800 devices.

 

What do I probably miss in my configuration to enable ZTP contact at rebooting / restarting a device?

 

Thanks,

 

Lothar

HP Recommended

Hello Lothar Behrens,


Once a phone is ZTP provisioned this turns the server off and the phone no longer checks for the ZTP server.

 

You would need to re-enable ZTP on the phone or factory reset the phone.

 

Config:

 

<code device.set="1" device.prov.ztpEnabled.set="1"  device.prov.ztpEnabled="0" />

Or via the GUI:

 

  • Menu => Settings => Advanced => Administrator Settings => Network Configuration => Provisioning Server => ZTP => Enable 

Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.

Best Regards

Steffen Baier

Polycom Global Services

------------------------------------------------
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.

Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.