-
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center. -
-
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center. -
- HP Community
- Poly Phones
- Desk and IP Conference Phones
- IP 7000 - No audible ring

Create an account on the HP Community to personalize your profile and ask a question

09-21-2017 11:23 AM
I did a firmware upgrade of an IP 7000, then did a Factory Reset and configured the phone. Everything seems to work however I don't get an audible ring. The leds blink, the screen shows 'ringing' but no ring sound. I set ring volume to max, and the ring type is set to low trill.
FW upgrade info:
Boot Block: 3.0.4.001
Boot Rom Updater: was 5.0.8.0935 now 5.0.12.0033
UC SIP: was 4.0.8.1972 now 4.0.12.0926
Any ideas on this?
Thanks...
Solved! Go to Solution.
Accepted Solutions
09-25-2017 11:35 AM
Hello DIFZ,
The backup seems to be imported back into the phone with many parameters not even supported by the phone so I suggest you factory default this unit and have it as a standalone device, register it to your SIP server, and then re-test.
The next step would be to work with your Polycom reseller.
In order to raise a support ticket you need to work with your Polycom reseller as they need to do this for you. End Customers are usually unable to open a ticket directly with Polycom support.
If this is some sort of an Internet discounter please post either your phone's MAC address or your Polycom devices serial so I can look up who would be able to support you. This may not be who you purchased the Polycom device from.
Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.
Best Regards
Steffen Baier
Polycom Global Services
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.
Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN
09-23-2017 05:27 AM
Hello DIFZ,
welcome to the Polycom Community.
Does the Loudspeaker work on the unit ? And did this work prior to the Upgrade ?
Does the phone pickup any configuration from a provisioning server or can you post a backup ?
Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.
Best Regards
Steffen Baier
Polycom Global Services
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.
Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN

09-25-2017 11:17 AM
Hi,
Yes the loadspeaker works. This is new phone (a month or two old) so I believe that it worked properly before the upgrade.
We can make/recieve calls OK. The call indicators work and if you pick up the call is fine, it just isn't ringing.
(I have other phones to upgrade however I don't want to do them yet, until I can figure this out.)
The upgrade was done by specifying a TFTP server (desktop) as the provisioning server.
Attached is the backup.
Thanks...
09-25-2017 11:35 AM
Hello DIFZ,
The backup seems to be imported back into the phone with many parameters not even supported by the phone so I suggest you factory default this unit and have it as a standalone device, register it to your SIP server, and then re-test.
The next step would be to work with your Polycom reseller.
In order to raise a support ticket you need to work with your Polycom reseller as they need to do this for you. End Customers are usually unable to open a ticket directly with Polycom support.
If this is some sort of an Internet discounter please post either your phone's MAC address or your Polycom devices serial so I can look up who would be able to support you. This may not be who you purchased the Polycom device from.
Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.
Best Regards
Steffen Baier
Polycom Global Services
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.
Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN