• ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
Are you having HotKey issues? Click here for tips and tricks.
HP Recommended

Greetings again. I ran into another issue with the computer. It seems fitting a double slot graphics card it not possible due to the CPU cooler in the way.

 

Any suggestions for an alternative? 

 

Maybe I should start a new thread

HP Recommended

@trentcreek,

 

Yes, I certainly have this suggestion/solution for you as I applied it to my HP EliteDesk 800 G3/G4/G5 SFF upgrade projects: I used a "90-degrees" PCIe x16 extension cable/graphics card stand/base, like this AliExpress purchase example:

 

NonSequitur777_3-1709178797285.png

 

Pulled the PCIe x16 ribbon cable through the desktop's rear PCIe bracket slots and plugged it in the desktop's PCIe x16 slot, and parked my graphics card outside the case -see the blue line:

 

NonSequitur777_1-1709177989433.png

 

If your power supply is fitted inside your desktop, you could also pull the PCIe 8-pin power cable(s) the same way to power your GPU. Later used a sturdier (LED lighted) graphics card base:

 

NonSequitur777_0-1709177893538.png

 

Hope this was helpful.

 

Kind Regards,

 

NonSequitur777


HP Recommended

Thanks for the quick and informative reply.

 

I don't think that would be a good match in my case due to many reasons including a young child who will be using this unit.

So the image is what I am dealing with. 

photo_2024-02-28_21-57-28.jpg

 

Looking at low profile coolers, even they appear they could be too high. I was looking at Tower Coolers, but they never post all sides, and the dimensions.

 

 

HP Recommended

@trentcreek,

 

All right, let's see how we can remedy this.  Please take the same picture at the same angle without the GPU.

 

Kind Regards,

 

NonSequitur777


HP Recommended

Here you go:

 

photo_2024-02-28_22-20-01.jpgphoto_2024-02-28_22-20-10.jpgphoto_2024-02-28_22-20-15.jpg

 

 

Edit:

 

I found this on NewEgg, and the description indicates support for LGA775

 

https://www.newegg.com/p/13C-00UY-00001

 

It appears like it could allow the graphics card some space, but they do not show an image of the installation kit.

HP Recommended

@trentcreek,

 

It's definitely a space issue.  Since I have had experience modifying a number of heatsinks, my thinking was that I would trim the heatsink if it wasn't more than, say, 1½ cm.

 

Btw, what's the part number of the heatsink?

 

Kind Regards,

 

NonSequitur777


HP Recommended

The heatsink part number is  577493-001

 

 

It does appear that Cr-1200 Cooler from China could work out. Found some images on eBay

 

cr-1200.jpg

 

Reexamining, no. I see the current heatsink also stops at the same spot as the CR-1200; right at the edge of the metal CPU  holder.

HP Recommended

@trentcreek,

 

Trimming* the heatsink is an option, though HP wouldn't approve, of course [disclaimer]:

 

NonSequitur777_2-1709183339345.png

 

Anyway, if you were to consider this, I would strongly recommend offsetting the loss of cooling ribs/aluminum by adding some copper cooling strips, like what I did here with my HP Compaq 8300 USDT upgrade project:

 

NonSequitur777_1-1709183291663.png

 

These heatsinks are very inexpensive, under $6 via eBay-US: HP Compaq 6000 6005 ELite 8000 SFF Socket T/LGA 775 Desktop Heatsink 577493-001 | eBay, so you could make this a little 'project' without breaking the bank.

 

Apparently, there are two different types of p/n: 577493-001 heatsinks (though it doesn't really matter):

 

NonSequitur777_3-1709183749930.png

 

* For these kinds of trimming/modding activities, I have used tools like these ones:

 

NonSequitur777_0-1709185327052.png

 

Kind Regards,

 

NonSequitur777


HP Recommended

Thanks for the time and tips you provided.  Searching, I found those "copper strips" are actually M.2 SSD drive heatsinks.

 

 

I did see some water cooling options. The inexpensive option puts the pump and cooler in a single package which raises the height too much. The expensive option does bring the height to an acceptable level allowing the graphics card to fix, but those are overly complex and expensive for such an old computer.

 

 I would prefer not to cut, but appears I will have to.

 

Thanks again for time and tips!

HP Recommended

@trentcreek,

 

Any time -glad I could assist!

 

Kind Regards,

 

NonSequitur777


† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.