Close Tray Message will not go away even when tray is closed.

[ChippSTC]

The tray holding the paper is closed but the screen doesn't allow printing.  it just says to close the tray.  We pulled the tray completely out and it looks like a piece way at the back is broken off.  Suspect that there is a sensor that isn't being hit which will not allow the printer to proceed with printing, scanning, etc. etc.

Is there a work around for this issue?

[Jeet_singh]

Hi @ChippSTC,

Thanks for engaging in HP support Forums! This is a wonderful location to converse with the community, get assistance and find tips! I understand you are having issues related to your HP Printer. Don't worry as I have a few suggestions which should help you resolve this issue.

To provide you with an accurate solution, I'll need a few more details:

Have you recently made any changes on the printer before the issue started?

In the meantime, let's try these steps here: 

Perform a Hard reset on the printer and make sure that the printer is connected directly to the wall outlet and not to the surge protector.

With the printer turned on, disconnect the power cord from the rear of the printer and also unplug the power cord from the wall outlet.

Remove USB cable, if present.

Wait for 2-3 minutes, press and hold the power button on your printer for about 30 seconds to remove any additional charge.

Now plug back the power cable straight to a wall outlet without any surge protector or an extension cord and then plug back the power cord to the printer.

Turn on the printer and wait till warm-up period finishes and the printer is idle.

If the issue persists, I would suggest here is to open and close the tray fully for about 8 to 10 times and check if that helps.

If this does not help, I would personally suggest this could be a possible hardware failure with the printer. I would recommend you contact our HP phone support for available service related options.

HP Technical Support can be reached by clicking on the following link: http://h22207.www2.hp.com/us-en/?openCLC=true

(1) Once the support page opens please select the country in which you're located. Next, enter your HP model number on the right.

(2) Next, choose the 'Contact Support' tab at the top and scroll down to the bottom of the 'HP Support- Contact' page to fill out the form provided with your contact information.

(3) Once completed click the 'Show Options' icon on the bottom right.

(4) Lastly, scroll down to the bottom of the page and select 'Get the phone number.' A case number and phone number will now populate for you.

If you have any troubles, let me know and I will do my best to help!

Hope this helps, for any further queries reply to the post and feel free to join us again

Feel free to post your query for any other assistance as well,

It's been a pleasure interacting with you and I hope you have a good day ahead.

If you wish to show appreciation for my efforts, mark my post as Accepted Solution.

And click on the Purple Thumbs up icon at the bottom of my comment.

Regards,

[Chad70]

I have followed all these steps.  There is nothing obstructing.  It continues to say paper tray open.

[kevin-t]

Hello,

Thank you for posting in this thread. Unfortunately based on when the last response was made, I have closed this thread to help keep comments current and up to date. We recommend starting a new thread for your issue by clicking here.
To be more helpful with your post, you can add key information if you desire: 
1. Product Name and Number (please do not post Serial Number)
• Example: HP Pavilion DV2-1209AX or HP Deskjet 3000 Printer CH393A
2. Operating System installed (if applicable)
• Example: Windows XP, Windows Vista 32-bit, Windows 7 64-bit
3. Error message (if any)
• Example: ""Low disk space"" error in Windows
4. Any changes made to your system before the issue occurred
• Examples: Upgrading your Operating System or installing a new software; or installing new hardware like a printer, modem, or router.
If you have any other questions about posting in the community, please feel free to send me a private message!

Thank you