• ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
Are you having HotKey issues? Click here for tips and tricks.
Common problems for Battery
We would like to share some of the most frequently asked questions about: Battery Reports, Hold a charge, Test and Calibrating Battery . Check out this link: Is your notebook plugged in and not charging?
HP Recommended
HP Envy x360 15-bq101ng
Linux

Hi,

 

I try to upgrade the Bios of my Laptop to F.07 Rev.A which was released on Feb 1, 2018. The file is called sp85085.exe

 

So far I have an USB Stick from HP which I boot using EFI into the Bios update menu: (Similar to Step 4: Update the BIOS in

https://support.hp.com/ie-en/document/c00042629)

 

The problem I have is that sp85085 contains two binary files but no corresponding *.sig files to verify. Only 08311.bin and 08312.bin, hence the update fails.

 

Furthermode I have the suspicion that they are anyway not the correct firmware files since the board id is 83C6, hence the binary should be named 083C6.bin?

 

Other failed attempts where booting the efi files in the CrisisFolder of sp85085.exe.

 

How can I update the Bios without any Bootable Windows available?

Thanks and BR CD

3 REPLIES 3
HP Recommended

Hi! @cd17, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!

 

I understand you have issues updating BIOS on your PC.

 

Don't worry I'll try to help you out.

 

Did you make any software or hardware changes on your PC?

 

Do you get any errors on the blue screen?

 

As you mentioned you have issue updating the BIOS on your PC to F.07.

 

Try restoring the BIOS to default on your PC and check if it helps.

 

1.    Turn off the computer and wait five seconds.
2.    Press the Power button to start the computer and repeatedly press the F10 key to enter the BIOS setup menu.
3.    On the BIOS Setup screen, press F9 to select and load the BIOS Setup Default settings.
4.    Press F10 to Save and Exit.
5.    Use the arrow keys to select Yes, then press Enter when asked Exit Saving Changes?
6.    Follow the prompts to restart your computer.
 

 

To perform a power reset on a laptop with a removable battery, use the following steps:
Turn off the computer.
Remove the computer from any port replicator or docking station.
Disconnect all external connected peripheral devices such as USB storage devices, external displays, and printers.
Unplug the AC adapter from the computer.
Remove the battery from the battery compartment.
With the battery and power cord unplugged, press and hold the Power button for about 15 seconds to drain any residual electrical charge from the capacitors.
Insert the battery and plug the AC adapter back into the laptop, but do not connect any of the peripheral devices.
Press the Power button to turn on the computer.
If a startup menu opens, use the arrow keys to select Start Windows Normally, and then press the Enter key.
After Windows opens, reconnect each peripheral device that was disconnected, one device at a time, until all devices are reconnected.
Your laptop has been reset. After a power reset, it is a good idea to run Windows Update and HP Support Assistant to update all device drivers. See Updating Drivers and Software with Windows Update (Windows 10, 😎 and Using HP Support Assistant (Windows 10, 8, 7) for more information.

 

 

After the reset try the steps recommended below.

 

Turn off the notebook.
Plug the notebook into a power source using the power adapter.
With the notebook off, press and hold the Windows logo key and the B key at the same time.
   NOTE:
On some notebook models, it might be necessary to press and hold the Windows logo key and the V key.
While pressing those keys, press and hold the Power button on the computer for 2 to 3 seconds, and then release the Power button but continue to hold the Windows logo key  and the B or V key until the HP BIOS update screen displays or you hear a beeping sound (usually 8 beeps).
The HP BIOS Update screen displays and the BIOS update begins automatically. This might take several minutes, and you might hear additional beeping sounds.
If the HP BIOS Update screen does not display, repeat the previous steps. If the issue persists after repeating the steps, skip to the next step to Download a replacement BIOS file.
If the Power light turns off, the notebook has turned off because the Power button was held too long. Repeat the previous steps, making sure to hold the Power button for 2 to 3 seconds only.
If your notebook starts Windows, update the BIOS to the latest version using the standard BIOS update procedure. For more information about updating your notebook BIOS, go to Updating the BIOS (Notebooks).
Click Continue Startup to prompt the notebook to restart immediately, or allow the notebook to restart automatically when the timer reaches zero.
After the notebook restarts, press Enter to continue.
   NOTE:
If the notebook repeatedly displays a message that the BIOS has been recovered, go to HP BIOS Application Selected is Corrupt or Missing for troubleshooting steps.
After Windows starts, if a message displays stating that the notebook was improperly shut down or that a boot problem was detected, follow the on-screen instructions.
You can now to enter the BIOS menu or start the Windows operating system.

 

Refer this article to further troubleshoot BIOS issues.

 

If the issue still persists after trying out the steps.

 

Please contact HP support for service options.

 

Link to contact HP.

 

 

If the solution provided worked for you, please mark accepted solution for this post.

 

Let me know if this helps!

Have a pleasant day ahead! 🙂

 

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

                                                                                                                  

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

A4Apollo
I am an HP Employee

HP Recommended

Hi @MrRobot, I tried all of that already. My Windows doesn't boot and I want to update the Firmware. HP provides no Signature files for the BIOS update, hence it's not possible.

 

Plz: either add signature files to your firmware update or add the bios to your hp pc hardware diagnostics 3-in-1 tool.

 

Thanks, BR CD

HP Recommended

@cd17, Thanks for your quick response and time.

 

I appriciate your efforts for writing back to us.

 

As you mentioned the issue still persists after trying out the steps.

 

I would suggest you contact HP phone support and get the support options.

 

The PC has to be shipped to a repair center to reload the BIOS.

 

Link to contact HP.

 

 

Have a great day ahead!

Take Care! 🙂

 

 

A4Apollo
I am an HP Employee

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.