Could't not find the firmware RSM4 for Seagate Hdd which come's with the HP laptop

[Sandeep1111]

In My Hp 15 AY516TX Laptop Seagate HDD Model Number: ST1000LM035-1RK172 not get initialize, after few research got to know that the HDD Firmware RSM4 is not displaying.

below is the information from CMD SEACHEST firmware. I already try to replace the same PCB but does not happen anything. 

And also its size is some thing 144.12 PB is displaying.

Can you please send the link where i can download the Firmware. 

Below is the detail info.

Serial Number:	WDE5M6KA		Part Number:	1RK172-020
Model Number:	ST1000LM035		Family:	BARRACUDA25

\\.\PhysicalDrive1 - 035-1RK172 - 090308E11D02 - ATA
SCSI Translator Reported Information:
Vendor ID: ST1000LM
Model Number: 035-1RK172
Serial Number: 090308E11D02
Firmware Revision: 0
World Wide Name: *****************************
Drive Capacity (PB/PiB): 144.12/128.00
Temperature Data:
Current Temperature (C): Not Reported
Highest Temperature (C): Not Reported
Lowest Temperature (C): Not Reported
Power On Time: Not Reported
Power On Hours: Not Reported
Max LBA: 281474976710654
Native Max LBA: Not Reported
Logical Sector Size (B): 512
Physical Sector Size (B): 512
Sector Alignment: 0
Rotation Rate (RPM): 7200
Form Factor: 2.5"
Last DST information:
Not supported
Long Drive Self Test Time: Not Supported
Interface speed:
Not Reported
Annualized Workload Rate (TB/yr): Not Reported
Total Bytes Read (B): Not Reported
Total Bytes Written (B): Not Reported
Encryption Support: Not Supported
Cache Size (MiB): Not Reported
Read Look-Ahead: Enabled
Write Cache: Disabled
SMART Status: Unknown or Not Supported
ATA Security Information: Not Supported
Firmware Download Support: Full, Segmented
Specifications Supported:
SPC-4
SBC-3
UAS
SPC-4
Features Supported:
Informational Exceptions [Mode 0]
ATA Reported Information:
Model Number: ST1000LM035-1RK172
Serial Number: WDE5LRDJ
Firmware Revision: RSM4
World Wide Name: ***********************************
Drive Capacity (EB/EiB): 18.45/16.00
Temperature Data:
Current Temperature (C): Not Reported
Highest Temperature (C): Not Reported
Lowest Temperature (C): Not Reported
Power On Time: Not Reported
Power On Hours: Not Reported
MaxLBA: 18446744073709551614
Native MaxLBA: Not Reported
Logical Sector Size (B): 512
Physical Sector Size (B): 512
Sector Alignment: 0
Rotation Rate (RPM): 7200
Form Factor: Not Reported
Last DST information:
Not supported
Long Drive Self Test Time: Not Supported
Interface speed:
Max Speed (Gb/s): 6.0
Negotiated Speed (Gb/s): Not Reported
Annualized Workload Rate (TB/yr): Not Reported
Total Bytes Read (B): Not Reported
Total Bytes Written (B): Not Reported
Encryption Support: Not Supported
Cache Size (MiB): Not Reported
Read Look-Ahead: Enabled
Write Cache: Enabled
Low Current Spinup: Disabled
SMART Status: Good
ATA Security Information: Supported
Firmware Download Support: Full, Segmented
Specifications Supported:
ATA8-ACS
ATA/ATAPI-7
ATA/ATAPI-6
ATA/ATAPI-5
ATA/ATAPI-4
SATA 3.0
Features Supported:
SATA NCQ
SATA Software Settings Preservation
SATA Device Initiated Power Management
HPA
Power Management
Security
SMART [Enabled]
DCO
48bit Address
GPL
SMART Self-Test
SMART Error Logging
Write-Read-Verify
EPC [Enabled]
SCT Write Same
SCT Error Recovery Control
SCT Feature Control
SCT Data Tables

[erico]

Firmware for Seagate HDD are located at the Seagate website.

I suggest that you use the hyperlink below to request the proper firmware from Seagate.

https://www.seagate.com/support/kb/firmware-updates-for-seagate-products-207931en/

[Sandeep1111]

Thanks you but i already tried same.

Below is the result from there.

Serial Number:	WDE5M6KA		Part Number:	1RK172-020
Model Number:	ST1000LM035		Family:	BARRACUDA25

Firmware

Name Importance Version Release Date Short Description Downloads and Actions

No Newer Firmware Available

-------

-------

17-Jul-22

A field update is not available for this serial number. See if CERTIFICATE Firmware Update is shown below. Please help us to improve the Download Finder - More...

Please read...

[erico]

Well, it would seem that there is no firmware update available. 

To initialize the disk, I suggest using the DiskPart utility.

You can boot from an ISO  in the same PC or put the disk in another PC to use DiskPart.