-
1
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center. -
-
1
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center. -
- HP Community
- Notebooks
- Notebook Hardware and Upgrade Questions
- Pavilion dv6t-7000 battery - Won't boot without AC and won't...

Create an account on the HP Community to personalize your profile and ask a question
08-07-2019 02:44 AM - edited 08-07-2019 02:46 AM
Hi,
I have the exact same problem as this link: https://h30434.www3.hp.com/t5/Notebook-Hardware-and-Upgrade-Questions/Battery-test-passed-but-wont-c...
Except I didn't upgrade to Win 10. One day, using the laptop on battery, the whole thing just shut down. It was a rather hot day, but system temperature wasn't more than 80*C. I couldn't boot it back up on battery, had to use AC adapter.
I did battery test and it passed with flying color. Battery 3 yr old Duracell, but barely degraded (battery test below). I don't understand how it could pass every test but still doesn't work. Seems like no current between battery and laptop, either something bad with the battery circuit board or the motherboard?
Battery currently holding 91%. It says "plugged in, charging" but it isn't charging. If I pull the AC plug, instant shutdown. Also notice, once I plug the AC in, it instantly boots even without pressing the power button.
Tried:
1) Hard reset
2) reflashed Bios
I'm not sure if I should buy a new battery b/c it might be the mobo that is damaged?
Warranty Type: 1
Cycle count: 41 / 300
Manufacturer: 13-15
Battery Age: 1001 days
Serial Number: 49175 11/09/2016
Temperature: 26 °C
Design Capacity: 5200 mAh
Full Charge Capacity: 4986 mAh (95%)
Remaining Capacity: 4532 mAh
Current: 0 mA
Terminal Voltage: 12203 mV
Design Voltage: 11100 mV
Cell Voltage 1: 4071 mV
Cell Voltage 2: 4067 mV
Cell Voltage 3: 4065 mV
Cell Voltage 4: 0 mV
Status: C0
AC Power: Yes
CT Number: N/A
Help much Appreciated!! Thanks!!
Solved! Go to Solution.
Accepted Solutions
08-08-2019 02:36 AM - edited 08-08-2019 02:39 AM
So much for the help community. And where are all these HP gurus?
Yeah, they'll just tell you to buy a new battery or a new laptop. Useless.
I'm going to tell you guys the answers, HP going to hate this.
Modern Lithium Ion batteries comes with smart circuit boards. These boards have a lot of protection breakers to prevent fire, explosion, etc... However, unlike a building breaker, you can't reset it with a button or something. Probably because they want you to buy new batteries.
There is a way to reset it though, yet not a single HP assistant has ever bother to tell anyone.
1) Open your battery. Use an exacto blade + flat head screw driver. Refer to youtube vids.
2) You do not need to remove the cell or the circuit board.
3) Connect a wire from the + pin on the connector to the + end of the lithium cells. Some batteries reset is on the - end, so do that too by connecting the wire to the - pin on the connector and the - end of the lithium cell. Do one or the other, not both at the same time! MAKE SURE you know which pins are + and - and which end of the cells are + and -. ONLY + to + OR - to -.
That's it. Battery chip reset. Run battery diagnostic. Everything good.
08-08-2019 02:36 AM - edited 08-08-2019 02:39 AM
So much for the help community. And where are all these HP gurus?
Yeah, they'll just tell you to buy a new battery or a new laptop. Useless.
I'm going to tell you guys the answers, HP going to hate this.
Modern Lithium Ion batteries comes with smart circuit boards. These boards have a lot of protection breakers to prevent fire, explosion, etc... However, unlike a building breaker, you can't reset it with a button or something. Probably because they want you to buy new batteries.
There is a way to reset it though, yet not a single HP assistant has ever bother to tell anyone.
1) Open your battery. Use an exacto blade + flat head screw driver. Refer to youtube vids.
2) You do not need to remove the cell or the circuit board.
3) Connect a wire from the + pin on the connector to the + end of the lithium cells. Some batteries reset is on the - end, so do that too by connecting the wire to the - pin on the connector and the - end of the lithium cell. Do one or the other, not both at the same time! MAKE SURE you know which pins are + and - and which end of the cells are + and -. ONLY + to + OR - to -.
That's it. Battery chip reset. Run battery diagnostic. Everything good.