Windows 10 Creators Update: Restart the system to upgrade the PCI Bus.

[leftfield01]

Hello.

I've upgraded Windows 10 Home 64 Bit to 1703 Creators Update.

Unfortunately I had to go back to my previous version (the 1511- build SO 10586.1176) because the 1703 gave me

problems with the PCI Bus. In particular, I appeared repeatedly at every boot (even after 2-3 days) a window,

accompanied by a notification, that was about rebooting the system to upgrade the PCI Bus. I looked into Device

Manager and I clicked on Detect hardware changes, but everything went perfectly. I have restart, in three days, at least

twenty times, but the window would appear at every startup:

The window says: "The hardware settings have been changed. Restart the computer to make these changes effective."

I thank anyone who can solve my problem.

Regards,

leftfield01.

[A4Apollo]

Hi! @leftfield01, Thanks for stopping by the HP Support Forums!

I understand after you upgraded your PC to 1703 Creators Update you are getting PCI Bus error on your PC.

Don't worry I'll to help you out.

Did you make any software or hardware changes on your laptop?

Please provide the product number of your PC to assist you better.

As you mentioned after you upgraded your PC to 1703 Creators Update you are getting PCI Bus error on your PC.

Try updating the BIOS and chipset drivers on your PC and check if it helps.

Link to update the BIOS and chipset drivers.

Try the steps recommended below.

Press Windows key + S and type troubleshooting in the search bar.
Select Troubleshooting.
Select View all on the top left corner.
Click on Hardware and Devices.
Follow the on-screen instructions to run the troubleshooter.
Restart the computer and see if the issue persists.

If the issue still persists try running HP support assistant on your PC and update the drivers on your PC.

Refer this article to know more information about using HP support assistant.

If the solution provided worked for you, please mark accepted solution for this post.

Let me know if this works!

Take Care! 🙂

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

[leftfield01]

Hi! MrRobot, thank you for having responded to me.
I have upgraded the drivers through the HP Support Assistant and also manually. The only driver that I did not update manually is the High Definition AMD (HD) graphics card driver. Instead I updated the High Definition AMD graphics card driver - Kabini. I updated the Bios but did not find the chipset driver update (until recently the chipset driver was referred to as the HP 3D DriveGuard (?) i've upgraded).
My product number is: F0D67EA#ABZ.
I'll let you know if what you've told me worked. It will take some time because I went back to Windows 10 Home 1511.

Regards,

leftfield01.

[Chimney_83]

Thanks for the reply, please try the suggested procedure and let me know if it worked. 

[leftfield01]

Of course, thank Chimney_83!

Regards.

[A4Apollo · Accepted solution]

@leftfield01, Thanks for your prompt response and time.

I'm sorry I was out of office, so I was not able to respond back to you.

Sure you can take your time and let me know if it worked.

If the solution provided worked for you, please mark accepted solution for this post.

Hope to hear from you soon!

Take Care! 🙂

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

[leftfield01]

Hi MrRobot, sorry for my delay. Your solution worked fine, but now I no longer find HP Recovery Manager because I had to do a clean installation at Windows 10 Fall Creators Update. How can I install HP Recovery Manager to reinstall all the software and more I had before? I tried installing the SP74123, but it did not work because I think it's just a Recovery Manager update. I had already created a recovery media in a USB key and I also have the recovery partition. Can I extract the Recovery Manager from there or do I have to return to Windows 10 Creators Update?

Thanks again for your precious support.

Regards,

leftfield01.

[MKazi]

@leftfield01

Hi,

You're most welcome. I'm glad to know that the suggested steps helped.

As @A4Apollo is out of the office today, I'm replying to you. 

I understand that the recovery manager program is no longer present in your laptop. However, you have the USB recovery manager and the recovery partition is still available in the laptop. 

Upon researching, I found that your HP laptop originally came with Win8 installed. Please refer to the steps mentioned under "Reinstalling software on HP notebook computers with Windows 8" from this HP document. 

NOTE: But since the recovery manager program is absent, you may launch the recovery manager by following the below steps:

• Shutdown the laptop.
• Power on the laptop and immediately hit the f11 key repeatedly (7-8 times) on the keyboard.
• This will launch the recovery partition.

Hope this helps. Good luck! 🙂