Envy x360 15-bq-108ca BIOS update F.17 error message "unknown command"

[lampuiho]

Running the update sp87238.exe on my 15-bq-108ca with F.13 bios, it displays the popup message "Erro: Unknown command." on the page Flashing BIOS with no progress at all and crashes afterwards. How do I fix this?

[A4Apollo]

Hi! @lampuiho, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!

I understand after updating the BIOS on your PC and you are getting unknown command error while updating the BIOS.

Don't worry I'll try to help you out.

Did you make any software or hardware changes on your PC?

Was there any hardware component replaced on your PC recently?

Try few steps recommended below.

To perform a power reset on a laptop with a removable battery, use the following steps:
Turn off the computer.
Remove the computer from any port replicator or docking station.
Disconnect all external connected peripheral devices such as USB storage devices, external displays, and printers.
Unplug the AC adapter from the computer.
Remove the battery from the battery compartment.
With the battery and power cord unplugged, press and hold the Power button for about 15 seconds to drain any residual electrical charge from the capacitors.
Insert the battery and plug the AC adapter back into the laptop, but do not connect any of the peripheral devices.
Press the Power button to turn on the computer.
If a startup menu opens, use the arrow keys to select Start Windows Normally, and then press the Enter key.
After Windows opens, reconnect each peripheral device that was disconnected, one device at a time, until all devices are reconnected.
Your laptop has been reset. After a power reset, it is a good idea to run Windows Update and HP Support Assistant to update all device drivers. See Updating Drivers and Software with Windows Update (Windows 10, 😎 and Using HP Support Assistant (Windows 10, 8, 7) for more information.

Try restoring the BIOS to default and check if it helps.

1.    Turn off the computer and wait five seconds.
2.    Press the Power button to start the computer and repeatedly press the F10 key to enter the BIOS setup menu.
3.    On the BIOS Setup screen, press F9 to select and load the BIOS Setup Default settings.
4.    Press F10 to Save and Exit.
5.    Use the arrow keys to select Yes, then press Enter when asked Exit Saving Changes?
6.    Follow the prompts to restart your computer.
 

After the reset try the steps recommended below.

Turn off the notebook.
Plug the notebook into a power source using the power adapter.
With the notebook off, press and hold the Windows logo key and the B key at the same time.
   NOTE:
On some notebook models, it might be necessary to press and hold the Windows logo key and the V key.
While pressing those keys, press and hold the Power button on the computer for 2 to 3 seconds, and then release the Power button but continue to hold the Windows logo key  and the B or V key until the HP BIOS update screen displays or you hear a beeping sound (usually 8 beeps).
The HP BIOS Update screen displays and the BIOS update begins automatically. This might take several minutes, and you might hear additional beeping sounds.
If the HP BIOS Update screen does not display, repeat the previous steps. If the issue persists after repeating the steps, skip to the next step to Download a replacement BIOS file.
If the Power light turns off, the notebook has turned off because the Power button was held too long. Repeat the previous steps, making sure to hold the Power button for 2 to 3 seconds only.
If your notebook starts Windows, update the BIOS to the latest version using the standard BIOS update procedure. For more information about updating your notebook BIOS, go to Updating the BIOS (Notebooks).
Click Continue Startup to prompt the notebook to restart immediately, or allow the notebook to restart automatically when the timer reaches zero.
After the notebook restarts, press Enter to continue.
   NOTE:
If the notebook repeatedly displays a message that the BIOS has been recovered, go to HP BIOS Application Selected is Corrupt or Missing for troubleshooting steps.
After Windows starts, if a message displays stating that the notebook was improperly shut down or that a boot problem was detected, follow the on-screen instructions.
You can now to enter the BIOS menu or start the Windows operating system.

Refer this article to further troubleshoot BIOS issues. Click Here

Try updating the latest version of BIOS using this link. Click Here

If the solution provided worked for you, please mark an accepted solution for this post.

Let me know if this helps!

Have a pleasant day ahead! 🙂

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

[lampuiho · Accepted solution]

 I have some time today so I used the installer to save the image to the disk. Then I mounted the EFI volume and copied the BIOS image to that location using CMD with admin rights. After that, I restarted and kept pressing F2 until diagnostic launched. Then I selected Update BIOS and selected the BIOS image from the EFI volume. And then it finished the update and verfied the BIOS image without any problem. Not sure why the installer in Windows was having trouble though.

[A4Apollo]

@lampuiho, thanks for writing back to us.

As you mentioned you installed the BIOS from EFI volume.

I'm glad to know your issue got resolved.

If you have any queries in future related to any HP products, you can always reach out to us.

We will try our best to help you out.

Take care,
Have a great day! 🙂