Poly Studio G62 how to install the hardware

[karlaz]

To ensure full functionality, the Poly Studio G62 system requires that you connect the following peripherals:

• Camera

• Microphone

• Speaker

• Monitor

• Controller

Your peripherals and configuration depend on the room size and room type.

Mounting your Poly Studio G62 system

You can mount the Poly Studio G62 using the supplied magnetic feet or the optional magnetic plate.

For information on mounting your Poly Studio G62 system, see the Poly Studio G62 Optional Mounting Plate and PoE Injector Quick Start Guide on the HP Support site.

 Required airflow clearance for a Poly Studio G62 system

 When installing your Poly Studio G62 system, provide adequate space for airflow..

CAUTION:

To avoid thermal issues with your Poly Studio G62 system, ensure that there is proper spacing away from the vent holes.

Connect monitors to the Poly Studio G62 system

Connect two monitors to the system to display far-side video and content.

 

Procedure

1. Connect one end of the HDMI cable to HDMI port 1 on the primary monitor.
2. Connect the other end of the HDMI cable to the HDMI 1 port on the Poly Studio G62 system.
3. Connect a second monitor to the HDMI 2 port on the Poly Studio G62 system.

Connect IP microphones to the Poly Studio G62 system

Connect up to three Poly IP microphones to the Poly Studio G62 system.

 

Note:

The Poly Studio G62 system LLN port doesn't provide power to connected peripherals. Use a PoE Ethernet switch or PoE injector to power your Poly IP peripherals.

Procedure

1. To provide power to your Poly IP microphones, connect a supported Ethernet switch, such as a Netgear A/V Line M4250 GSM4210PD, to the LLN port on the Poly Studio G62 system.

   If you're connecting only one Poly IP microphone, you can use a PoE injector.

2. Using the cables supplied with your Poly IP microphones, connect the microphones to the Ethernet switch.

   Alternatively, you can connect the microphones using a CAT5e, CAT6, or CAT7 direct STP Ethernet cable. The cable can be up to 91 m (300 ft) in length.

3. After powering on your system, finish setup by accessing the system web interface.
   1. In the system web interface, go to Device Management > Available Devices.
   2. Next to the Poly IP microphone entry, select Pair.

Connect a USB camera to the Poly Studio G62 system

Connect a supported or compatible USB camera to your Poly Studio G62 system.

Note: Power off the system before connecting or disconnecting USB cameras.

Note: If you connect a third-party camera to the system, camera controls may be limited or unavailable. Poly DirectorAI features such as camera tracking and DirectorAI Perimeter aren't available.

Procedure

• Using the USB cable that shipped with your camera, connect the camera to an available USB-A port on the Poly Studio G62 system.

  When the Poly Studio G62 system starts, the camera displays in the system web interface under General Settings > Device Management under Connected Devices.

Connect a 3.5mm audio output device to the Poly Studio G62 system

Connect an audio output device such as an amplifier or sound bar to your system using the 3.5mm audio output port.\

External amplifiers may have other settings that must be changed. Third-party amplifiers and speakers should be tuned for proper operation per manufacturer guidelines and audio industry standards.

If your audio device has an option for fixed or variable audio, choose variable to allow audio output adjustment from the system controller.

Procedure

1. Connect the speaker to the 3.5mm output port on the system.

   Make sure the 3.5mm connector is fully seated in the connector.

2. In the system web interface, go to Audio/Video > Audio > Line Out.
3. Select Variable.
4. From the Speaker Options drop down menu, choose Line Out.
5. Go to Audio/Video > Audio > General Audio Settings.
6. Verify that Transmission Audio Gain (dB) is set to 0dB.

Connect a USB audio DSP to your Poly Studio G62 system

Connect a supported audio DSP to your system to handle audio input and output.

Procedure

1. Connect a USB cable from the audio DSP to a USB Type-A connection on the system.
2. In the system web interface, go to Audio / Video > Audio and enable the Enable USB Audio check box.

   The system saves your changes automatically.