Guidelines
We have new content about printers, Click here to check it out!
Check some of the most frequent questions about Instant Ink: HP INSTANT INK, HP+ PLANS: INK AND TONER.


Check out our WINDOWS 11 Support Center info about: OPTIMIZATION, KNOWN ISSUES, FAQs AND MORE.
HP Recommended
HP OfficeJet Pro 9025 All-in-One Printer
Microsoft Windows 10 (64-bit)

my HP OfficeJet Pro 9020 series printer has been stopping with the display stating that there is failure to upload an update, but there is apparently no update available. when this happens i have to unplug the printer and re-plug in the printer to have it restart, afterwhich it works for a while and then stops working saying there is a software update in the small onboard screen. I have tried the HP Print and Scan Doctor, which says there is no update to be loaded. Any ideas? Thank you.

1 REPLY 1
HP Recommended

Hi @Ron653,

 

Welcome to the HP Support Community. 

 

I'd like to help!

 

Disable automatic firmware update on the HP Officejet pro series

 

To disable automatic firmware updates from the Control Panel/ Front Panel, follow the instructions below:

On the control panel/ front panel of the printer touch Setup or the Gear Icon 

 

  1. Then scroll down to Printer Maintenance and select it. Then Scroll down to Update the Printer and select it.
  2. Under update the printer, select “Printer Update Options” and select the option “Do not check”. When asked to confirm the settings, please select Yes. 

Link for Printer Control Panel Document: https://support.hp.com/ph-en/document/ish_5817551-5817617-16

 

If you are unable to change the Printer Update options and if you are getting a message, this option is locked. Then you might have to restore factory defaults on the printer. To do so, please follow the instructions below:

On the control panel/ front panel of the printer touch Setup or the Gear Icon 

 

  1. Then scroll down to Printer Maintenance and select it. Then scroll down to Restore and select it.
  2. Then select Restore Factory defaults. When prompted to confirm the action, please select Yes. 

This will restore the printer to factory defaults and the printer will restart. Once the printer is restarted, On the control panel/ front panel of the printer touch Setup or the Gear Icon 

 

  1. Then scroll down to Printer Maintenance and select it. Then Scroll down to Update the Printer and select it.
  2. Under update the printer, select “Printer Update Options” and select the option “Do not check”. When asked to confirm the settings, please select Yes.
  3. Then connect the printer back to the network.

 

To disable automatic updates from the EWS (Embedded Web Server) page of the printer, follow the instructions below:

  1. Open a browser and enter the IP address of the printer in the address bar. 

Link for the document on how to find the IP address of the printer: https://support.hp.com/us-en/document/ish_6039801-6039767-16 

  1. You might the below message 
  2. In the EWS page of the printer click on Tools Tab, then click on Printer Updates and click on “Firmware Updates”. Then select the option Do not check of Updates and click on Apply. Refer to the image below for the same. 
  3. If the option “Do not check of updates is disabled, then you will have to restore factory defaults of the printer. To restore factory defaults on the printer, access the EWS page of the printer and click on the Settings Tab. Then click on Restore Defaults and click on “Restore Factory Defaults. Refer to the image below for the same. 
  4. After restoring factory defaults, the printer will restart. Then you will have to connect the printer to the network. Once the printer is connected to the network, you access the EWS page and of the printer click on Tools Tab, then click on Printer Updates and click on “Firmware Updates”. Then select the option Do not check of Updates and click on Apply.

Note: This is a temporary workaround. Once we have a new firmware update available on HP.com you will have to follow the same steps and manually enable automatic firmware updates. 

 

If the firmware update changes back to Automatic again, follow the above procedure to disable automatic firmware update and then access the EWS page of the printer and change the firmware settings. To do so, follow the instruction below:

  1. In the EWS page of the printer click on Settings, then click on Security and click on Administrator Settings.
  2. Then Scroll down to Printer Updates and uncheck “All Firmware Updates” and click on Apply. 

 

Note: When you enable web services on the printer, you might get a prompt to check for updates, choose no. If you choose yes, by default the Check for updates will automatically be selected and that will enable automatic updates. 

 

Hope this helps! Keep me posted for further assistance.
Please click “Accepted Solution” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos/Thumbs Up" on the bottom right to say “Thanks” for helping!

Nal_NR-Moderator
I am an HP Employee

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.