-
1
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center. -
-
1
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center. -
- HP Community
- Printers
- Printer Setup, Software & Drivers
- Printer failure message HP Officejet 7612

Create an account on the HP Community to personalize your profile and ask a question
10-10-2022 06:24 AM
HP Officejet 7612 Shows massage: Printer failure
“There is a problem with the printer or ink system. Press OK to try to recover. If problem persists turn printer off, then on. Contact HP if you continue to get this message."
But I don’t see any “OK” button.
10-13-2022 04:04 AM
Hi @Sebastiaan94,
Welcome to the HP Support Community.
I understand that you are getting a printer failure error. I'd like to help!
To provide you with an accurate solution, I'll need a few more details:
Have you done any hardware changes to the printer?
Are you using a genuine HP ink cartridge?
However, I suggest you do a Hard Reset
(1) Turn the printer on, if it is not already on.
(2) Wait until the printer is idle and silent before you continue.
(3) With the printer turned on, disconnect the power cord from the rear of the printer.
(4) Unplug the power cord from the wall outlet.
(5) Wait at least 60 seconds.
(6) Plug the power cord back into the wall outlet.NOTE: HP recommends connecting the printer power cord directly to the wall outlet.
(7) Reconnect the power cord to the rear of the printer.
(8) Turn on the printer, if it does not automatically turn on.
The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.
Wait until the warm-up period finishes and your printer is idle and silent before you proceed.
Remove the ink cartridges
Removing the ink cartridges and checking for an error message can help diagnose the printer issue. Take the ink cartridges out of the printhead, and then check the printer control panel or computer for an error message.
Open the ink cartridge access door.
The carriage moves to the left side of the access area.
Wait until the carriage is idle and silent before proceeding.
Push in on the front of one of the ink cartridges to release it, and then pull the ink cartridge toward you to remove it.
Figure : Removing the ink cartridge
Repeat these steps for the other ink cartridges.
Close the ink cartridge access door.
Check the control panel to see if an error message displays.
If the printer displays an Ink System Failure message on the control panel, skip to the step to Update the printer firmware.
If the message has changed to Replace the,
,
, or
Ink Cartridge, continue to the next step.
Clean the ink cartridges, and then check the error message
Cleaning the ink cartridge contacts, and then reinstalling the ink cartridges one at a time can help determine if a specific ink cartridge is causing the error message.
Gather the following materials:
A clean, lint-free cloth
A clean, dry cotton swab
Distilled or bottled water
CAUTION:
Do not use tap water because it might contain contaminants that can damage the printhead.
Lightly dampen a clean, lint-free cloth with bottled or distilled water.
Gently wipe the copper-colored contact on one of the ink cartridges.
Figure : Wiping the copper-colored contact
Wipe the contact with a dry, lint-free cloth before proceeding to the next step.
Repeat these steps for the three remaining ink cartridges.
Carefully reinsert one of the ink cartridges into its slot, and then push the ink cartridge forward until it clicks into place.
Figure : Reinserting the ink cartridge
Make sure each colored dot on the ink cartridge label matches the colored dot on the print carriage.
Figure : Matching the colored dot on the print carriage
Close the ink cartridge access door.
Check the printer control panel to see if the error message persists.
If the message is to Replace the,
,
, or
Ink Cartridge, remove the specified ink cartridge(s) and clean the copper-colored contact again, and then reinsert the ink cartridge(s).
You may go through the document here Printer Failure and see how it goes.
Hope this helps! Keep me posted.
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution. Click the “Yes" on the bottom right to say “Thanks” for helping
Nal_NR-Moderator
I am an HP Employee
10-15-2022 06:55 AM
Hi @Sebastiaan94
As we did not hear from you, I'll be closing this case for now. Hope I was able to fix the issue. If you need further assistance, feel free to reach out to us.
Nal_NR-Moderator
I am an HP Employee