Problem with partial reset hp officejet 8610 pro

[markoevolution]

I did a partial reset, from the printer's hidden menu, but I cannot complete the configuration because a cartridge error appears on the display, which does not allow me to continue to configure the printer and restart it.
Because of this, the carriage with the cartridges does not move and remains fixed to the right, so I cannot even remove the cartridges.
What can I do?
Thank you.

[Nal_NR]

Hi @markoevolution,

Welcome to the HP Support Community. 

I'd like to help!

It looks like a carriage jam. 

Perform the following tasks in the order given. Use the printer after each task to see if the issue is resolved.

Check for obstructions in the carriage path

Remove any loose paper or obstructions that might be blocking the carriage path.

If the Cancel button on the control panel is lit, press it and wait until the printer is silent.

Turn off the printer, and then disconnect the power cord.

Open the cartridge access door to get to the carriage inside the printer.

EXAMPLES OF A CARTRIDGE ACCESS DOOR

Make sure the carriage is not obstructed by gently sliding the carriage side to side.

Look for and remove any obstructions in the carriage path, such as crumpled paper or dislodged labels.

CAUTION:

Do not tilt an ink tank printer when attempting to remove obstructions as ink might spill.

EXAMPLE OF A PRINTER WITH AN OBSTRUCTION IN THE CARRIAGE PATH

If the carriage has a latch, gently press it down to make sure it is locked into place.

CAUTION:

If the carriage latch of an ink tank printer is secured, do not press down on it to avoid printer damage.

EXAMPLES OF THE CARRIAGE LATCH

If the carriage is not locked in place, move it to each side, removing any obstructions blocking its path.

CAUTION:

Do not force the carriage to move if it is locked or stuck. This can damage the printer.

Close the printer door.

Reconnect the power cord, and then turn on the printer.

Click here for the remaining steps. 

Hope this helps! Keep me posted for further assistance.
Please click “Accepted Solution” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos/Thumbs Up" on the bottom right to say “Thanks” for helping!

[markoevolution]

Bye,
thank you for your reply.
My problem, however, is that the printer is not configured. The error that comes up on the display means that I cannot continue the installation after the partial reset. This results in the cartridge carriage being stuck to the right, and pushing it manually does not move it. Is there any way to unlock it? I am convinced that by removing the cartridges (which I remind you are original), the error on the display would no longer appear and I could complete the configuration.

[Nal_NR]

Hi @markoevolution,

If there is a carriage jam, then Perform the following tasks in the order given. Use the printer after each task to see if the issue is resolved.

Check for obstructions in the carriage path

Remove any loose paper or obstructions that might be blocking the carriage path.

If the Cancel button on the control panel is lit, press it and wait until the printer is silent.

Turn off the printer, and then disconnect the power cord.

Open the cartridge access door to get to the carriage inside the printer.

EXAMPLES OF A CARTRIDGE ACCESS DOOR

Make sure the carriage is not obstructed by gently sliding the carriage side to side.

Look for and remove any obstructions in the carriage path, such as crumpled paper or dislodged labels.

CAUTION:

Do not tilt an ink tank printer when attempting to remove obstructions as ink might spill.

EXAMPLE OF A PRINTER WITH AN OBSTRUCTION IN THE CARRIAGE PATH

If the carriage has a latch, gently press it down to make sure it is locked into place.

CAUTION:

If the carriage latch of an ink tank printer is secured, do not press down on it to avoid printer damage.

EXAMPLES OF THE CARRIAGE LATCH

If the carriage is not locked in place, move it to each side, removing any obstructions blocking its path.

CAUTION:

Do not force the carriage to move if it is locked or stuck. This can damage the printer.

Close the printer door.

Reconnect the power cord, and then turn on the printer.

Reset the printer

Reset the printer to recover from printer errors or failures.

If your printer has a rechargeable battery, remove it.

With the printer turned on, disconnect the power cord from the printer.

Unplug the power cord from the power source.

Wait 60 seconds.

Reconnect the power cord to a wall outlet and to the printer.

NOTE:

HP recommends plugging the printer directly into a wall outlet.

Turn on the printer to complete the reset.

Service the printer

Service or replace your HP product if the issue persists after completing all the preceding steps.

Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.

To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.

Please click “Accepted Solution” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos/Thumbs Up" on the bottom right to say “Thanks” for helping!

[markoevolution]

Bye,
the fact is that you keep giving me standard solutions, but my problem is different. I have no paper jam, the cartridge carriage does not move, as I have not completed the installation of the printer firmware, after the partial reset.
This is because I get a cartridge error on the display, which causes me to fail to complete the installation.

[Nal_NR]

Hi @markoevolution ,

We are sorry that the issue is not resolved when the above troubleshooting steps were performed.

This might require one-on-one interaction to fix the issue via remote assistance. 

I've sent you a private message with further instructions. In order to access your private messages, click the private message icon on the upper right corner of your HP Support Community profile, next to your profile Name or simply click on this link.

If the information I've provided was helpful, give us some reinforcement by clicking the Accepted Solution button, that'll help us and others see that we've got the answers!